DP AIR GOMETER Panduan Pemilik - Halaman 8

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Peralatan Kebugaran DP AIR GOMETER. DP AIR GOMETER 15 halaman.

Halaman Cetak
IMPORTANT
PLEASE READ ALL ASSEMBLY INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY.
Assembly Instructions
FIGURE
1
Step
1.
Remove
the
HANDLEBARS (No.
1),
CONNECTING RODS (No.
2),
SEAT
(No.
3), FRAME (No.
4),
FOOT TUBE
(No.
5), console
carton,
and
the
hardware bag from the carton.
NOTE:
Be sure
that
all parts have
been
removed before discarding carton.
Step
2.
Attach
FOOT
TUBE
(No.
5)to
FRAME
(No.4)with
SCREWS (No. 6) and LOCKNUTS (No.
7).
Step
3'
Push LARGE SHOULDER BUSHINGS
(No.
8), with
SHOULDER
to outside, into CONNECTING RODS
(No.
2)
as
shown
in
FIGURE
1
and DETAIL
"A".
NOTE:
FLAT SIDE of
CONNECTING
RODS must
be
to
inside as shown in DETAIL
"A".
Step
4.
READ ALL OF STEP 4 BEFORE ATTACHING PEDALS
NOTE: The PEDALS are
NOTthe
same and
must
be
assembled
to
the proper CRANK.
Be
sure to match
the
colored
Iabe|s
of
CRANKS & PEDALS.
Attach
PEDALS (No.
9
HIGHT &
10
LEFT) to corresponding CRANKS (No. 128 RIGHT & 129 LEFT) with CONNECT-
ING
RODS (No.
2) and
PLASTIC
SPACERS
(No.
11).
PLASTIC
SPACERS are positioned
between CONNECTING
RODS and CRANKS - see DETAIL "A".
Tighten,
with
9/16"
WRENCH, both
PEDALS
very tightly
by turning toward
REAR
of
UNIT.
Step
5.
Push PLASTIC EXPANSION NUTS
(No.
12) into FRAME CROSSBRACE.
Step
6.
Attach CONSOLE BRACKET
(No.
13)to
FRAME (No.
4)with SCREWS
(No.
14).
NOTE:
Use
only
two SCREWS
in
the
front two holes
at
this time.
Step
7.
Pull gently
on
the SPEED
PICKUP WIRE
to
remove any slack wire within
the
FRAME (No.
4).
Step
B.
Attach
BRACKET
COVER
(No.
15)to
CONSOLE BRACKET (No.
13)
with
remaining
two SCREWS
(No.
14).
Step
9.
Slide CONSOLE (No.
16)
over
ends
of CONSOLE BRACKET (No.
13),
with
"DP"
towards
FRONT, and fasten with
KNOBS (No.
17).
Step'10.
Remove MONITOR (No. 18)lrom CONSOLE (No.
16),
open BATTERY
DOOR,
insert BATTERIES
(4 "AA"
Alkaline
batteries, NOT
INCLUDED), and replace BATTERY DOOR.
Step11.
ThreadSPEEDP|CKUPW|REthroughbackof CONSOLE(No.16),plugintobackof MONITOR(No.18),andreplace
MONITOR in CONSOLE.
NOTE: Tuck excess WIRE under MONITOR as it is replaced in CONSOLE.
Step
12.
Attach HANDLEBARS
(No.
1)to
FRAME
(No.4)with
PIVOT RODS (No.
19).
Tighten with wrench.
NOTE: When properly mounted,
a
HANDLEBAR
will
have its HANDLE pointing away from the AIR
GOMETERTM.
Step
13.
Thread
FOOT SUPPORT
(No.20)onto
PIVOT RODS (No. 19) and tighten
with
pliers.
Step
14.
Moisten with water or liquid soap, and
push
FOOT SUPPORT CUSHIONS (No.
21)
over
FOOT SUPPORTS (No.
20).
Step
15.
Push SMALL
SHOULDER
BUSHINGS (No.
22)
into holes
in
front
end of
CONNECTING
RODS (No.
2).
Step
16.
Push SMALL SHOULDER BUSHINGS (No. 22), CONNECTING RODS (No. 2), and 3/8" WASHERS (No.
23)
onto
PINS at end
of HANDLEBARS
(No.
1)
and fasten
with
HAIRPIN
COTTERS
(No.
24).
NOTE:
1.Due
to smallvariations in
manufacture, HAIRPIN
COTTER
may
not
fit
into hole
in
PIN
when
using two
3/8"
WASHERS.
lf
this occurs,
remove one
of
the 3/8" WASHERS.
NOTE: 2.HAlRPlN COTTER
must
be
inserted properly
-
see
DETAIL
"B'.
Step
17.
Remove LOCKNUTS
from SEAT
(No. 3) and attach SEAT to
SEAT
POST (No.
106)with
LOCKNUTS.
Step
18.
Slide SEAT
(No.
3)to
desired height,
align
the nearest
hole
in
the SEAT
POST
(No. 106)with holes
in
SEAT
POST
TUBE,
insert, and
tighten
SEAT
ADJUSTMENT
KNOB (No.
25).