Electrolux AON-C31 Petunjuk Instalasi

Jelajahi secara online atau unduh pdf Petunjuk Instalasi untuk Kulkas Electrolux AON-C31. Electrolux AON-C31 1 halaman. Side-by-side refrigerator

Halaman Cetak

I n s t a l l a t i o n I n s t r u c t i o n s

WARNING

To avoid electric shock, which can cause death or severe personal injury, do not connect your

refrigerator to an electrical power source until you have completed Step 3 of these instructions.

Tools Necessary:

AND

Socket

Adjustable

™

Phillips Head

Wrench Set

Wrench

Prepare The Installation Site

Your refrigerator is designed to be part of a built-in kitchen cabinet system. Be

sure to coordinate site preparation and installation with your kitchen contractor.

Include these minimum guidelines in your site preparation:

• Choose a place near a grounded electrical outlet.

• Do not use an extension cord or an adapter plug.

• Avoid direct sunlight and close proximity to a range, dishwasher or other

heat source.

• Floor should be level and able to support a fully loaded refrigerator.

• The refrigerator's Ice & Water Dispenser requires water supply access.

• Plan for easy access to counter tops when removing food.

• For complete access to drawers and freezer baskets, doors must be able

to fully open.

Allow the following clearances for ease of installation, proper air circulation, and

plumbing and electrical connections:

Sides & Top: 3/8 inch

Rear: 1 inch

Transport Unpackaged Refrigerator To Site

By now, you have already removed your refrigerator's shipping carton. You may still

need to use a hand truck to move it through close spaces or entrances. If the

refrigerator is larger than an entrance, consider two options:

• Remove the entrance door if one exists.

• Remove the refrigerator doors (see how in your Use & Care Guide).

When using a hand truck:

• Load refrigerator from side of cabinet only.

• Do not run retaining straps over handles.

• Do not over-tighten retaining straps.

• Never use refrigerator handles to move the refrigerator.

• Remove tape from doors only after unit is in place.

Shifting the refrigerator from side to side

may damage flooring.

Connect Water Supply

What you will need:

CAUTION

eçìëÉ

• Access to a cold water line

éäìãÄáåÖ

To avoid property damage:

with pressure of

äáåÉ

• Use copper tubing for the water

30-100 psi.

supply line (plastic tubing is more

• Copper tubing with ¼-inch

likely to leak).

(6.4mm) OD. Length for

t~íÉêäáåÉ=Üççâìé

• Ensure water supply complies with

this tubing is the distance

íÜÉ ï

local plumbing codes.

from the rear of the refrigerator to your household

water supply line plus 7 feet (2.1 meters).

NOTE

• A shut-off valve for the connection between your household

water line and the refrigerator supply line.

Electrolux Kit #53039117950, available from

Do not use a self-piercing shut-off valve.

your dealer, provides all materials for a water

• A compression nut and ferrule (sleeve) for the water supply

supply installation, including 25 feet of

connection at the rear of your refrigerator.

copper tubing and full instructions.

Not satisfied with the installation of your refrigerator?

S i d e - B y - S i d e R e f r i g e r a t o r

f o r

To connect the water supply to the rear of your refrigerator:

1 Ensure that the refrigerator is not plugged in.

2 Flush the supply line until water is clear by placing the end of the

copper tube in a sink or bucket and opening the shut-off valve.

3 Remove the plastic cap from the water valve inlet at the rear of

NOTE

your refrigerator. Discard the cap.

4 Slide the brass compression nut, then the ferrule (sleeve) onto

These installation

copper tube.

instructions are provided

5 Push the copper tube into water valve inlet as far as it will go

only as a possible customer

(1/4 inch).

option. Electrolux

6 Slide the ferrule (sleeve) into valve and finger-tighten the

recommends that you use a

compression nut onto valve. Tighten another half turn with a

service or kitchen

wrench. Do not over-tighten.

contracting professional to

7 Secure the copper tube to your refrigerator's rear panel with a

install your refrigerator.

steel clamp and screw (see illustration).

8 Coil the excess copper tubing (about 2½ turns) behind your

refrigerator as shown. Arrange coiled tubing to avoid vibration or

wear against other surfaces.

9 Open water supply shut-off valve and tighten any connections

that leak.

NOTE

NOTES

TES

Information about

cabinetry construction for

• The ice maker's fill valve may operate noisily if the household water supply is shut off.

Electrolux products is

• After ensuring no water leaks exist at any connection, be sure to check for leaks again in 24 hours.

available for contractors.

• See your Use & Care Guide for detailed information about setting up and operating the Ice & Water

Call 1-877-435-3287.

Dispensing system.

UTION

CAUTION

UTION

Place In Permanent Position

Room temperatures below

55°F (13°C) or above

110°F (43°C) will impair

If possible, use a hand truck to position the refrigerator directly in front of

cooling ability of your

its cabinet enclosure.

refrigerator's compressor.

Be careful not to move the refrigerator beyond its water supply (copper

tubing) connections.

Plug in the power cord, and push the refrigerator straight back into

place.

IMPOR

IMPORT T T T T ANT

If you are installing your refrigerator without connecting it to a water

supply, make sure the ice maker's power switch is turned Off (see the

Use & Care Guide for more details).

Level Refrigerator & Adjust Doors (if necessary)

Guidelines for final positioning of your refrigerator:

• All four corners of the cabinet must rest firmly on the floor.

CAUTION

UTION

• The cabinet should be level at the front and rear.

• The sides should tilt ¼-inch (6 mm) from front to back (to

ensure that doors close and seal properly).

• Doors should align with each other and be level.

All of these conditions can be met by raising or lowering the adjustable front rollers.

To level the cabinet using the front rollers:

Open both doors and remove the toe grille by gently pulling forward

UTION

(see illustration 1).

Close the doors and use a flat-blade screwdriver or 3/8 inch socket

wrench to raise or lower the front rollers. (See illustration 2.)

Ensure both doors are bind-free with their seals touching the cabinet

on all four sides.

To level the doors using the lower hinge:

If the refrigerator door is lower than the freezer door, raise the

refrigerator door by turning the adjustment screw clockwise. (See

illustration 3.)

If the freezer door is lower than the refrigerator door, raise the

freezer door by turning the adjustment screw clockwise. (See

illustration 3.)

Ensure door stop flange is touching hinge flange. If not, readjust as necessary.

(See illustration 4.)

Replace the toe grille by fitting it into place.

This document should only be removed by customer after installation.

CAUTION

UTION

• Shifting the refrigerator from

side to side may damage

flooring.

• Do not block the toe grille on

ANT

the lower front of your

refrigerator. Sufficient air

circulation is essential for

proper operation.

Please contact the store you purchased it from.

Remove Internal Shipping Materials

Electrolux uses packing foam and tape to secure the internal parts of your refrigerator for shipping. Once the

refrigerator is in position, you can remove this material.

Location of these materials may vary depending on your model.

Problems? Try These Suggestions

Operation problems are possible if any of the installation tasks are not completed. Here is a list of things to check

for:

• Is the refrigerator's power cord plugged in?

• Is the refrigerator connected to the household water supply?

• If you had to remove the refrigerator and freezer doors, did you reattach water and power connectors at the

door hinges? (See the Use & Care Guide for detailed instructions on removing and replacing doors.)

• Is the ice maker power switch turned On?

Other possibilities to check:

• Is the power to the receptacle turned on?

• Is the water filter above the fresh food compartment fully seated (see Use & Care Guide for details)?

If you still have operation problems after checking these suggestions, please see the "Solutions To Common

Problems" section in your Use & Care Guide.

What's Next?

Congratulations. You are ready to begin enjoying your new Electrolux refrigerator.

• To become aware of important safety instructions and learn how to operate your refrigerator, please read the

entire Use & Care Guide.

• You may want to start with the "Normal Operating Sights & Sounds" section of the Guide to learn more about

what to expect during typical operation.

• Please register your product. You can register online at www.electroluxusa.com. or you can simply send in the

Registration Card.

And thank you for choosing Electrolux.

Installation Checkoff List

Doors

Ice Maker

Handles are secure and tight

House water supply connected to refrigerator

Door seals completely to cabinet on all sides

No water leaks present at all connections -

Freezer door is level across the top

recheck in 24 hours

Ice Maker is turned ON.

Leveling

Ice & Water Dispenser operates correctly

Front filter must be flush with filter housing (some

Refrigerator is level, side to side and tilted 1/4" (6mm)

models)

front to back

Toe grille is properly attached to refrigerator

Final Checks

Cabinet is setting solid on all corners

Shipping material removed

Electrical Power

Fresh Food and Freezer temperatures set

Crisper Humidity controls set

House power turned on

Registration Card sent in

Refrigerator plugged in

P/N: 241868801