Bosch 2 Panduan Petunjuk Pengoperasian - Halaman 23

Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian untuk Mesin pencuci piring Bosch 2. Bosch 2 26 halaman. Mini blender
Juga untuk Bosch 2: Panduan Instalasi Cepat (16 halaman), Panduan untuk Instalasi dan Penggunaan (18 halaman), Manual Petunjuk Asli (13 halaman), Manual Petunjuk Asli (22 halaman), Buku Petunjuk (32 halaman), Panduan Pengguna (28 halaman), Panduan Pengguna dan Petunjuk Instalasi (16 halaman), Buku Petunjuk (42 halaman), Panduan Petunjuk Pengoperasian (8 halaman), Buku Petunjuk (8 halaman), Buku Petunjuk (12 halaman), Panduan Memulai Cepat (2 halaman), Panduan Memulai Cepat (9 halaman), Buku Petunjuk dan Petunjuk Instalasi (36 halaman), Panduan Pengguna dan Petunjuk Instalasi (48 halaman), Panduan Referensi Cepat (2 halaman), Panduan Pengguna dan Petunjuk Instalasi (24 halaman), Buku Petunjuk (42 halaman), Informasi Untuk Penggunaan (28 halaman), Panduan Pengguna (40 halaman), Panduan Pengguna dan Petunjuk Instalasi (35 halaman), Panduan Pengguna (24 halaman)

Halaman Cetak
Bosch 2 Panduan Petunjuk Pengoperasian

Electrical connection

– Connect the appliance to an
alternating current only, ranging from
220 V to 240 V and 50 Hz or 60 Hz
via a correctly installed socket with
protective earth conductor. See rating
plate for required fusing 9*.
– The socket must be near the appliance
and freely accessible following
installation.
If the plug is not freely accessible, an
allpole disconnector with a contact
opening of at least 3 mm must be
fitted on the installation side to satisfy
the relevant safety instructions.
– The connection may be modified by
technicians only.
– A power cord extension may be
purchased from customer service only.
– Use only a residual current operated
circuit-breaker which features
the symbol ‚. Only this extension
guarantees compliance with
the currently valid regulations.
– The appliance features a water
damage protection system. Please
note the system will not function
unless the power supply is connected.

Removing the appliance

Also observe the sequence of worksteps
here.
– Disconnect the appliance from
the power supply.
– Turn off the water supply.
– Disconnect the waste water and fresh
water connections.
– Loosen fastening screws for the
furniture parts.
– If fitted, remove the base panel.
– Pull out the appliance, carefully pulling
the hose behind.

Transportation

Empty the dishwasher and secure loose
parts.
Drain the appliance according
to the following steps:
– Turn on the tap.
– Open the door.
– Switch on ON/OFF switch (.
– Select programme @ with
the highest temperature button < H.
– Press START button h.
– Close the door.
Programme sequence starts.
– Open door after approx. 4 minutes.
– Press START button h
for approx. 3 sec.
The Cleaning display X goes out.
– Close the door.
The remaining programme sequence
lasts approx. 1 minute more. (Buzzer
sounds.)
– Switch off ON/OFF switch (.
– Turn off the tap, disconnect supply
hose and drain water.
Transport appliance upright only.
(This prevents residual water from running
into the machine control and damaging
the programme sequence.)
Protection against frost
If the appliance is in a room where there is
a risk of frost (e.g. holiday home), empty
the appliance completely (see
Transportation).
aus
P r o t e c t i o n a g a i n s t f r o s t ( E m p t y i n g t h e a p p l i a n c e )
23