Bosch 6 Series Panduan Petunjuk Pemasangan dan Pengoperasian - Halaman 29

Jelajahi secara online atau unduh pdf Panduan Petunjuk Pemasangan dan Pengoperasian untuk Mesin pencuci piring Bosch 6 Series. Bosch 6 Series 36 halaman. 2 door top freezer, inox-easyclean
Juga untuk Bosch 6 Series: Panduan Pengguna (24 halaman), Petunjuk Instalasi dan Penggunaan Manual (20 halaman), Petunjuk Instalasi dan Penggunaan Manual (20 halaman), Petunjuk Instalasi dan Penggunaan Manual (20 halaman), Buku Petunjuk dan Petunjuk Instalasi (48 halaman), Buku Petunjuk (16 halaman), Buku Petunjuk (48 halaman), Panduan Petunjuk Instalasi (27 halaman), Buku Petunjuk (12 halaman), Buku Petunjuk (16 halaman), Petunjuk Instalasi dan Penggunaan Manual (16 halaman), Petunjuk Penggunaan Manual (29 halaman), Panduan Pengguna dan Petunjuk Instalasi (16 halaman), Informasi Untuk Penggunaan (32 halaman), Panduan Referensi Cepat (2 halaman), Panduan Referensi Cepat (2 halaman), Informasi Untuk Penggunaan (28 halaman), Panduan Pengguna (23 halaman), Buku Petunjuk (24 halaman), Petunjuk Instalasi Dan Petunjuk Penggunaan (24 halaman), Informasi Untuk Penggunaan (16 halaman), Panduan Pengguna (36 halaman), Panduan Pengguna (32 halaman), Panduan Pengguna (28 halaman), Panduan Pengguna (28 halaman), Buku Petunjuk (28 halaman), Informasi Untuk Penggunaan (20 halaman), Buku Petunjuk (28 halaman)

Bosch 6 Series Panduan Petunjuk Pemasangan dan Pengoperasian
3

Faults and what to do about them

F a u l t s a n d w h a t t o d o a b o u t t h e m
Faults
ð in the display panel
and drying has been
interrupted.
é in the display panel.
Dryer does not start.
Display panel goes off
and Start button flashes.
Creasing.
Water is leaking out.
Change in the pro-
gramme duration dis-
played during drying.
Laundry is not dried cor-
rectly or is still too damp.
*
Depending on the model
Cause/remedy
Empty the condensate container; ~ Page 25 and the dryer; ~ Page 13.
If the optional condensation drain is installed, the drain hose may be
blocked. Check the hose for deposits and flush the hose out.
Clean the fluff filter and/or the heat exchanger, then select the Start button
~ Page 24; ~ Page 27.
Mains plug plugged in or fuse checked?
Programme selected? Select a programme.
Dryer door open? Close the door.
Is the childproof lock activated? Deactivate the child-proof lock.
"Ready in" time selected? Programme starts after a delay.
Not a fault. Energy-saving mode is active ~ Page 11.
Creasing occurs when you have exceeded the maximum load or selected
the wrong programme for the type of fabric. All the required information
can be found in the programme table.
Remove clothes immediately after drying; creasing may occur if they are
left in the drum.
Not a fault; the dryer may be positioned on an incline. Level the dryer.
Not a fault. The moisture sensors detect the remaining moisture in the load and
adjust the programme length (except timed programmes).
After the end of the programme, warm laundry feels damper than it actually
is. Spread the laundry out and allow the heat to disperse.
Finely adjust the dryness level – this extends the drying time but does not
increase the temperature. Your laundry becomes drier ~ Page 21.
Select a programme with a longer drying time or increase the drying level.
This does not increase the temperature.
Select a time programme for subsequent drying of laundry that is still damp
~ Page 19.
If you have exceeded the maximum load for the programme, the laundry
may not be dried properly.
Clean the moisture sensor in the drum. The sensor may become covered by
a fine layer of limescale or residues of detergents and care products which
then impair its function. Your laundry is not being dried correctly
~ Page 28.
Drying has been interrupted as a result of a power cut, because
the condensate container is full or because the maximum drying time has
been exceeded.
Note:
See also the laundry tips ~ Page 18.
Faults and what to do about them
en
29