AirStage AJH040LBLAH Panduan Instalasi - Halaman 14
Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Pendingin Udara AirStage AJH040LBLAH. AirStage AJH040LBLAH 19 halaman. Outdoor unit
Halaman Cetak
Setting number (00xx)
Setting number (01xx)
Electricity meter
······
pulse setting 2 *3
73
Setting number (98xx)
Setting number (99xx)
Set the hundreds digit and thousands digit of the electricity meter pulse setting connected
to CN135.
(Forbidden)
90
(Factory default)
*1: Do not set this for outdoor units with Slave setting.
*2: When electricity meter No. is set to "000" and "201 to 299", the pulses input to CN135
become ineffective. Available setting number is "001" to "200"
*3: When the electricity meter pulse setting is set to "0000", the pulses input to CN135
become ineffective. Available setting number is "0001" to "9999"
(1) Turn on the power of the outdoor unit and enter standby mode.
• When system is normal
POWER/MODE lamp lights up. (ERROR
lamp is off.)
POWER/MODE
ERROR
POWER
ERROR
MODE
lamp: OFF
lamp: ON
LED101
LED102
(GREEN)
(RED)
7 segment
LED105
LED104
display:
turn off
MODE
ENTER
SELECT
ENTER
/EXIT
button
MODE/EXIT
SW107
SW108
SW109
button
SELECT button
(2) Setting method
Use the "MODE/EXIT", "SELECT", and "ENTER" buttons to confi gure settings according
to the procedures below.
(If no setting is made, the factory default setting will be displayed.)
: Press the "MODE/EXIT" button
: Press the "SELECT" button
: Press the "ENTER" button.
: Press the "ENTER" button for more than 3 seconds.
1: Function setting
First 2 digits
Last 2 digits
7 segment LED display
(LED 105, LED 104)
(Flashing)
(When [F3] to [F9] are displayed, continue to press the
"SELECT" button until [F2] is displayed.)
En-13
0
0
0
1
7
3
···
···
9
8
9
9
9
0
0
0
• When system is abnormal
Check the settings as there is an error in
the settings for outdoor unit address
(DIP switch SET 3-1, 2) or number of
connected slave units (DIP switch SET
3-3, 4).
POWER
ERROR
POWER/MODE
MODE
ERROR lamp:
lamp: ON
Blinking
LED101
LED102
(GREEN)
(RED)
LED105
LED104
7 segment
display: "-"
display
MODE
SELECT
ENTER
/EXIT
SW107
SW108
SW109
2: Setting the fi rst
Every press of the
"SELECT" button will
change the setting
number for the fi rst 2
digits.
EXIT: Press the "MODE/EXIT" button to cancel the setting mode.
7.5. Address setting for signal amplifi ers
7.5.1 Address setting for signal amplifi ers
When using signal amplifi ers, the address for signal amplifi ers must be set.
The address for signal amplifi ers can be set automatically from 1 outdoor unit (master
unit) on the network.
Refer to "Fig. Wiring example for automatic address setting" (7.6.1 chapter) for the wiring
example.
(For manual setting of address, refer to the signal amplifi er installation manual.)
7.5.2 Automatic address setting for signal amplifi ers
When setting the address of the signal amplifi er, please use the factory setting. (See the
installation manual of the signal amplifi er)
• When the system is normal, nothing will be displayed on the 7 segment display.
• When ERROR is displayed, inspect the units.
Use the "MODE/EXIT", "SELECT", and "ENTER" buttons on the outdoor unit PC board to
confi gure settings according to the procedures below.
2 digits
3: Setting the last 2 digits
Continue to press the "SELECT" button until the
desired number appears at the last 2 digits.
Setting is complete when the lamp lights up
Press "ENTER" button to return to "2. Setting the
fi rst 2 digits" (If there is no operation for 5 seconds
after the setting, the display will return to "2: Setting
the fi rst 2 digits".)
(Continue to press the "SELECT"
button until the desired number
appears at the last 2 digits.)
Setting is complete when the lamp lights up
Press "ENTER" button to return to "2. Setting the
fi rst 2 digits" (If there is no operation for 5 seconds
after the setting, the display will return to "2: Setting
the fi rst 2 digits".)