Dragonfly DFRM-TAB-100-MW Instal Manual - Halaman 6

Jelajahi secara online atau unduh pdf Instal Manual untuk Layar Proyeksi Dragonfly DFRM-TAB-100-MW. Dragonfly DFRM-TAB-100-MW 9 halaman. Recessed in-ceiling motorized projection screen
Juga untuk Dragonfly DFRM-TAB-100-MW: Panduan Instalasi (17 halaman)

Halaman Cetak

Step 8. Connect Control Wiring

E XT Control Connection

1 2 3 4 5 6

(Gold pins facing up)

1 2 3 4 5 6

Pin 6 - Up

Pin 5 - Down

Pin 4 - Stop

Pin 3 - Common

Pin 2 - RS232 Data Receive (RXD)

Pin 1 - RS232 Data Transmit (TXD)

IR Receiver

Connect the included IR receiver to the EXT IR port for IR control up to 26ft away and at a maximum

angle of 30°. Mount the receiver using the adhesive foam tape on the back.

Note:

The included IR receiver is proprietary to Dragonfly projection screens. Third party IR

receivers will not work.

3-12V DC Trigger

Connect the included 33' trigger wire from the TRIG port on the screen to the control out port of a

compatible projector for automatic control based on the projector.

RS232 Serial Control

Use pins 1 and 2 on the EXT CTRL port for one-way control. See the DFM Motorized Screen Control

Protocol documentation for driver and command information, available on the product page's

support tab.

To connect the wiring, either cut the included 10' RJ12 control cable and splice it to the correct wires or

terminate a cable using a 6P6C RJ11/12 connector.

Contact Closure/Relay Control

The Dragonfly motorized screen may also be controlled via contact closure or relay control.

Momentarily short the Common wire to the Up, Down, or Stop wire for the desired operation. The

screen stops automatically once a limit is reached, or the Stop function may be used to stop at any

desired position.

To connect wiring, either cut the included 10 foot RJ12 control cable and splice to the correct wires or

terminate a cable using a 6P6C RJ11/12 connector.

External IR Receiver

3.5mm Mono for

remote 3-12V DC

trigger

Step 9. Adjust Screen Travel

Set the final height of the screen during use and the closed position of the screen when not in use.

Limits are set using the RF remote and the limit adjustment button on the motor assembly.

Accessing the Adjustment Button

Open the access panel on the bottom of the housing by pulling down away from the magnets and

sliding the panel away from the viewing area. The button is next to the edge of the screen material.

Open Limit Adjustments

Stand in reach of the screen adjustment button while holding

the RF remote.

2. With the screen in the closed position, press the Down button

on the RF remote.

3. Once the screen has traveled within 6 inches of the desired

limit, press the adjustment button on the motor to stop the

screen.

4. Press the button repeatedly to adjust the screen to the

desired limit.

5. Once the screen is in the desired position, press the Up button on the RF remote. The setting is

saved.

Closed Limit Adjustments

Stand in reach of the screen adjustment button while holding

the RF remote.

2. With the screen in the open position, press the Up button on

the RF remote.

3. Once the screen has traveled within 6 inches of the desired

limit, press the adjustment button on the motor to stop the

screen.

4. Press the button repeatedly to adjust the screen to the

desired limit.

5. Once the screen is in the desired position, press the Down

button on the RF remote. The setting is saved.

Note:

Make sure to stop the screen using the adjustment button while there are several inches

of screen still exposed. Allowing the screen to travel too far into the housing causes the

bottom bar to travel too far into the housing. If this occurs, remove the screen from the

housing and unwrap the bottom bar enough to hang from the opening again.

Screen travel

adjustment button