Bosch Aquatak Clic 140 Manual Petunjuk Asli - Halaman 10
Jelajahi secara online atau unduh pdf Manual Petunjuk Asli untuk Mesin cuci Bosch Aquatak Clic 140. Bosch Aquatak Clic 140 16 halaman.
Halaman Cetak
10 | English
Assembly
For Your Safety
Warning! Switch off, remove plug from
mains before adjusting, cleaning or if cable
is cut, damaged or entangled.
Aquatak Clic 125/Aquatak Clic 130
Your pressure washer is double insulated for
safety and requires no earth connection. The op-
erating voltage is 230 V AC, 50 Hz (for non-EU
countries 220 V, 240 V as applicable). Only use
approved extension cables. Contact your Bosch
Service Centre for details.
Aquatak Clic 135/Aquatak Clic 140
Your pressure washer requires an earth connec-
tion. The operating voltage is 230 V AC, 50 Hz
(for non-EU countries 220 V, 240 V as applica-
ble). Only use approved extension cables. Con-
tact your Bosch Service Centre for details.
If you want to use an extension cable when op-
erating your high pressure washer, only the fol-
lowing cable dimensions should be used:
2
- 1.5 mm
– max length 20 m
2
- 2.5 mm
– max length 50 m
Note: If an extension cable is used it must be
earthed and connected through the plug to the
earth cable of your supply network in accord-
ance with prescribed safety regulations.
If in doubt contact a qualified electrician or the
nearest Bosch Service Centre.
WARNING! Inadequate extension cables
can be dangerous. Extension cable, plug
and socket must be of watertight construc-
tion and intended for outdoor use.
Cable connections should be kept dry and off
the ground.
It is recommended for increased electrical safe-
ty to use a Residual Current Device (RCD) with
a tripping current of not more than 30 mA. Al-
ways check your RCD every time you use it.
If the supply cord is damaged, it must be re-
placed by a Bosch Service Centre.
F 016 L70 545 | (14.1.11)
Products sold in GB only: Your product is fitted
with an BS 1363/A approved electric plug with
internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets,
it should be cut off and an appropriate plug fit-
ted in its place by an authorised customer serv-
ice agent. The replacement plug should have the
same fuse rating as the original plug.
The severed plug must be disposed of to avoid a
possible shock hazard and should never be in-
serted into a mains socket elsewhere.
Products sold in AUS and NZ only: Use a resid-
ual current device (RCD) with a rated residual
current of 30 mA or less.
Assembly
Assembly of Product (see figure A)
Fix the top handle 1 to the pressure washer us-
ing screws 12.
Fix the holder to the pressure washer using
screws 13.
Slide detergent tank into position as shown.
Connecting high pressure gun to lance
(see figures B and E)
Insert the 4 jet-lance 7 into power gun 8. De-
press and turn the jet-lance 90° clockwise to
lock in place.
Connecting high pressure hose to gun
(see figures C–D)
Join high pressure hose to gun as shown.
Secure with clip 14 as shown, check if secure by
pulling on high pressure hose.
Water connection (see figures H and J)
Screw inlet connector 5 onto machine water in-
let connection 15.
Attach water supply hose (not supplied) to the
mains water supply and machine.
High pressure hose/Supply cable
(see figures I and K)
Pull out the pressure hose 3 and supply cable 6
of the pressure washer.
Bosch Power Tools