Bosch Programme Table Buku Petunjuk - Halaman 8

Halaman Cetak

Insert for liquid detergent

Position the insert for dispensing liquid detergent:

– Remove the detergent drawer completely

– Slide the insert forwards.

Do not use the insert (slide upwards):

– For gel-type detergents and washing powder,

– for programmes with + Prewash

Care

Machine housing, control panel

– Remove detergent residue immediately.

– Wipe with a soft, damp cloth.

– Do not clean with a jet of water.

Cleaning the detergent drawer ...

... if it contains detergent or fabric softener residues.

1. Pull out, press insert down, remove drawer completely.

2. To remove the insert: press the insert upwards from below with your finger.

3. Clean the detergent dispenser tray and insert with water and a brush and dry it.

4. Fit the insert and lock it in place (push the cylinder onto the guide pin).

5. Push in the detergent drawer.

Leave the detergent drawer open so that any residual water can evaporate.

Drum

Leave the washing machine door open so that the drum can dry out.

Use chlorine-free cleaning agent, not steel wool.

Descaling

Ensure there is no laundry in the machine

This should not be necessary if the correct detergent dosage has been used. If it is necessary, however, proceed

according to the descaling agent manufacturer's instructions. Suitable descalers can be obtained via our website or

from our after-sales service (

page 13).

Instructions in the display panel

flashing

Close the washing machine door properly; laundry may be caught.

Open the tap completely, supply hose kinked or trapped; Clean the filter

water pressure too low.

Detergent solution pump blocked; Clean the detergent solution pump

Drain hose/waste pipe blocked; Clean the drain hose on the siphon

Water in the base tub, appliance leaking. Call the after-sales service.

Other displays

Switch off the appliance, wait for 5 seconds and switch it back on. If the display appears again,

call the after-sales service

depending on model

page 10.

(Finished in) option

– Risk of electric shock. Disconnect the mains plug.

– Risk of explosion. No solvents.

depending on model

page 11.

page 13.

Information about blockages

Detergent solution pump

Turn the programme selector to Off and disconnect the mains plug.

1. Open and remove the service flap.

2. Take the drain hose out of the retainer.

Remove the sealing cap, allow the detergent solution to flow out.

Push the sealing cap back on.

3. Unscrew the pump cover carefully (residual water).

4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent

solution pump must be able to rotate).

5. Replace the pump cover and screw it on tightly. The handle points upright. Replace the

drain hose in the holder.

6. Refit the service flap and close it.

To prevent unused detergent from flowing straight into the drain during the next wash:

Pour 1 litre of water into compartment II and start the Drain

Drain hose on the siphon

Turn the programme selector to Off and disconnect the mains plug.

1. Loosen the hose clamp, remove the drain hose carefully (residual water).

2. Clean the drainage hose and siphon connecting piece.

3. Reattach the drainage hose and secure the connection with the hose clamp.

Filter in the water supply

Risk of electric shock

Do not immerse the AquaStop safety device in water (contains electric valve).

Reduce the water pressure in the supply hose:

1. Turn off the tap.

2. Select any programme (except Spin

page 11,

3. Press

Start/Reload. Let the programme run for approximately 40 seconds.

4. Turn the programme selector to Off. Disconnect the mains plug.

Clean the filter:

5. Disconnect the hose from the tap.

Clean the filter with a small brush.

and/or on standard and Aquasecure models:

Remove the hose from the back of the appliance,

remove the filter using pliers and clean the filter.

6. Connect the hose and check for leaks.

Risk of scalding.

– Allow the detergent solution to cool down.

– Turn off the tap.

programme.

/ Drain