Draper MC1 Manual Pengkabelan - Halaman 4

Jelajahi secara online atau unduh pdf Manual Pengkabelan untuk Layar Proyeksi Draper MC1. Draper MC1 8 halaman. Low voltage, remote control, serial and network wiring
Juga untuk Draper MC1: Brosur (16 halaman), Petunjuk Manual (18 halaman)

Halaman Cetak

Draper Low Voltage, Remote Control, Serial and Network Wiring Guide

Wiring Diagram for Two-Way Serial Communication with RS232 and low voltage Radio Frequency Remote Control

➀ Wire Screen according to diagram.

➁ Before you can send commands, the RF receiver must "learn" the remote

transmitter. When the RF receiver ﬁ rst receives power, a red LED on the

bottom of the receiver activates. This means it is in learning mode. To

"learn" the transmitter, simply point it at the RF receiver and hold down the

"up" button until the red LED goes out.

➂ Once the remote is learned, press "Up" to test the screen. If screen goes

down, then the motor direction needs to be reversed. Press and hold

"Stop" for ﬁ ve seconds, then press the "Up" button. Motor directions will

now be reversed.

➃ To learn a second transmitter (up to ﬁ ve total allowed), press the "learn"

button on the bottom of the receiver, and repeat step 2 (you will have 10

seconds after pressing the "learn" button).

Wire to connect power to MC1 should be between 18 AWG and 12 AWG (solid or stranded) 2 conductors with ground. Wire size needs to be sufﬁ cient to

carry the motor load. Red and Black wires are the "open" and "close" leads from the motor. The MC1 comes enclosed in a metal box conforming to the National

Electric Code (NEC) with appropriate spacing between the wires and any exposed parts of the box. RF receiver is connected to MC1 using low voltage modular

data or telephone cord (RJ11), which is isolated from the AC power line. This wire is commonly called Silver Satin. It must be electrically straight (see explana-

tion on page 2). The RF Receiver must be within 1,000 feet of the MC1, must have a power supply, and must run through a splitter before the MC1. Power

supply can power up to three input devices. A dry contact wall switch may also be connected to the MC1 using 3-conductor wire.

Wiring Diagram for Two-Way Serial Communiation with RS232 and low voltage Infrared Remote Control

➀ Wire Screen according to diagram.

➁ Press "Up." If screen goes down, Press and hold "Stop" for ﬁ ve seconds,

then press the "Up" button. Motor directions will now be reversed.

Wire to connect power to MC1 should be between 18 AWG and 12 AWG (solid or stranded) 2 conductors with ground. Wire size needs to be sufﬁ cient to

carry the motor load. Red and Black wires are the "open" and "close" leads from the motor. The MC1 comes enclosed in a metal box conforming to the National

Electric Code (NEC) with appropriate spacing between the wires and any exposed parts of the box. IR Eye is connected to MC1 using low voltage modular data

or telephone cord (RJ11), which is isolated from the AC power line. This wire is commonly called Silver Satin. It must be electrically straight (see explanation on

page 2). The IR eye must be within 100 feet of the MC1. A dry contact wall switch may also be connected to the MC1 using 3-conductor wire.

White-Common

Red-to Screen (directional)

Brown-to Screen (directional)

Black-Hot to 110-120V AC

Program LED

Green/Yellow-Ground

Fuse

RS232 Data FROM Control System

RS232 Data TO Control System

Signal Ground & Manual Switch Common

Manual Switch Down

Manual Switch Up

MC1

Electrically Straight

Data Cable

Program LED

Fuse

MC1

Eye Port

www.draperinc.com

(765) 987-7999

Low Voltage Wiring by others

AC Wiring by electrician

Electrically Straight

Data Cable

Splitter

RF Transmitter

Transmitter range: 100 feet

White-Common

Red-to Screen (directional)

Brown-to Screen (directional)

Black-Hot to 110-120V AC

Green/Yellow-Ground

Low Voltage Wiring by others

AC Wiring by electrician

RS232 Data FROM Control System

RS232 Data TO Control System

Signal Ground & Manual Switch Common

Manual Switch Down

Manual Switch Up

IR Eye

Electrically Straight

Data Cable

IR Transmitter

Transmitter range: 70 feet

page 4 of 8

Power

Supply

RF Receiver