Draper Silhouette C Series Petunjuk Pemasangan & Pengoperasian - Halaman 2
Jelajahi secara online atau unduh pdf Petunjuk Pemasangan & Pengoperasian untuk Layar Proyeksi Draper Silhouette C Series. Draper Silhouette C Series 2 halaman. Manually operated projection screens
Juga untuk Draper Silhouette C Series: Panduan Pemasangan/Pengoperasian Dengan Suku Cadang Pengganti Servis (5 halaman)
Halaman Cetak
Silhouette/Series M and Series C by Draper
Mounting on 6" extension wall brackets: Brackets are not supplied with
screen and must be ordered separately.
Locking screw
"Z" Clip*
Angle adapter*
Pan head screw
Hex nut
Extension bracket
* Provided with screen
Side view of assembled extension bracket
Attach right angle adapter to top of extension bracket as shown using (1)
pan head screw and (1) locking nut. Attach (1) "Z" Clip wall mounting
bracket (supplied with screen) to front of extension bracket as shown using
(1) pan head screw and (1) locking nut. (Make sure "Z" Clip is oriented 90°
to angle adapter.)
Wall mount the extension brackets to wall, making sure they are level and
vertically plumb. Installer must insure fasteners are of adequate strength
and suitable for chosen mounting surface. Back out the top stop screw until
it is flush with front side of angle adapter.
Engage the lip on back of screen case with lip of "Z" Clip and gently pull
down to fully engage case to brackets. Screw in stop screw on each bracket
to lock screen case in place.
Locking screw
Wall bracket*
Angle adapter*
Extension
bracket
*Supplied with screen
Operating Instructions
Series M Spring Operated Screen: To lower picture surface, pull screen
down to desired position. Hesitate —then allow screen to slightly retract
very slowly until it locks in place.
To raise picture surface, pull down on the pull bail, then raise quickly, as a
window shade. Keep control of the picture surface. Do not allow it to roll
uncontrolled into the case, or damage is sure to result.
Series C Crank Operated Screen: To lower screen surface, attach the
crank handle to the "U" joint stud located on the left hand side of the screen.
With the crank handle in its operating position, rotate counterclockwise. An
internal pin within the gear box will stop the screen when fully extended. The
crank handle can be removed if desired. The shipping support brackets
must be removed from each end of dowel during initial operation.
Angle adapter
Wall bracket
Pan
head
screw
Extension Arm
Front view of assembled
extension bracket
To raise screen surface, attach the crank handle to the "U" joint stud located
on the left hand side of the screen. With the crank handle in its operating
position, rotate in a clockwise direction. An internal pin within the roller will
stop the screen when fully retracted. The crank handle can be removed if
desired.
90˚
Case fascia is removable to access roller assembly. To remove fascia,
depress outward the spring lip located inside lower front corner of screen
case and pull lower corner of fascia outward. Repeat this at right end of
case. Support fascia from center and rotate lower front edge upward
approximately 40° to disengage the Roll-Lok hinge at the top front of screen
case. Fascia can now be completely removed from case.
To install fascia, generally reverse instructions above making sure the Roll-
Lok hinge is completely engaged before rotating fascia down towards the
closed position. Depress spring clips outward, push lower corners of fascia
inward until lips of spring clips hook behind fascia.
Silhouette/Series M
1½"
Viewing Surface
Silhouette/Series C
3
2
/
"
8
If you encounter any difficulties installing or servicing your screen, call your
dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999, fax (765) 987-
7142, or e-mail [email protected].
Removing Case Fascia
4¾"
6"
Case Dimensions
Page 2 of 2