Bosch WAE-24463 BC Buku Petunjuk - Halaman 2
Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Mesin cuci Bosch WAE-24463 BC. Bosch WAE-24463 BC 8 halaman. Washing machine
Safety instructions
– Read the instruction manual and installation instructions and all other information enclosed with the washing
machine and act accordingly.
– Retain the documents for subsequent use.
Risk of electric shock
Danger to life
Danger of suffocation
Risk of poisoning
Risk of explosion
Risk of injury
Consumption values
Programme
(Cottons) 30 °C**
(Cottons) 40 °C**
(Cottons) 60 °C**
(Cottons) 60 ºC*
(Cottons) 90 °C**
(Easy-care)
40 °C**
>>
(Quick/mixed fabrics) 40 °C**
/
silk)
/
silk) 30 °C**
/
(Wool)
/
(Wool) 30 °C
* Programme setting for testing and energy labelling in accordance with EU directive 92/75/EEC.
** Programme setting for testing in accordance with valid standard EN60456.
Note on comparative tests: For testing the test programmes, wash the specified load using the maximum spin speed.
As a short programme for coloureds, select the programme >>
with the maximum spin speed.
*** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient tem-
Downloaded From WashingMachine-Manual.com Manuals
perature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected additional
7
functions.
Pflege (Care)
Before washing for the first time
Do not load any laundry into the machine. Turn on the tap. Add the following to compartment II:
– approx. 1 litre water
– detergent (dosage according to the manufacturer's instructions for light soiling and the appropriate
– Never pull the cable to disconnect the mains plug.
degree of water hardness)
– Never insert/disconnect the mains plug with damp hands.
Set the programme selector to
end of the programme, turn the programme selector to
For worn-out appliances:
Machine housing, control panel
– Disconnect the mains plug.
– Sever the mains cable and discard along with the plug.
– Wipe with a soft, damp cloth.
– Destroy the lock on the washing machine door. This will prevent children from
– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
locking themselves in and risking their lives.
– Remove detergent and cleaning agent residue immediately.
– Do not clean with a jet of water.
– Keep packaging, film and packaging parts out of the reach of children.
Cleaning the detergent drawer ...
– Keep detergents and care products out of the reach of children.
... if it contains detergent or fabric softener residues.
– Items of laundry pretreated with cleaning agents containing solvents, e.g. stain
remover / cleaning solvent may lead to an explosion after being loaded into the
1.
Pull out, press insert down, remove draw completely.
washing machine.
Rinse items of laundry thoroughly by hand beforehand.
2.
To remove the insert: press the insert upwards from below with your finger.
– The washing machine door can become very hot.
3.
Clean the detergent dispenser tray and insert with water and a brush and dry it.
– Be careful when draining hot detergent solution.
4.
Attach the insert and engage (connect the cylinder to the guide pin).
5.
Push in the detergent drawer.
– Do not climb onto the washing machine.
– Do not lean on the open washing machine door.
– Do not reach into the drum if it is still rotating.
Leave the detergent drawer open so that any residual water can evaporate.
– Be careful when opening the detergent drawer while the machine is in operation.
Drum
Leave the washing machine door open so that the drum can dry out.
Rust stains - use chlorine-free cleaning agent, not steel wool.
Additional
Electricity con-
Programme
Descaling
Load
Water
***
function
sumption
***
duration
***
Descale the appliance according to the descaler manufacturer's instructions. This should not be
7 kg
0.55 kWh
60 l
2:36 h
necessary if the correct dosage of detergent is used.
7 kg
0.69 kWh
60 l
2:36 h
Emergency release, e.g. in the event of a power cut
7 kg
1.33 kWh
60 l
2:39 h
The programme continues to run when the power has been restored. However, if the laundry has to
be removed, the washing machine door can be opened as follows:
EcoPerfect*
7 kg
1.05 kWh
47 l
3:08 h
Risk of scalding.
7 kg
2.00 kWh
64 l
2:47 h
The detergent solution and laundry may be hot. If possible, leave it to cool
down.
3 kg
0.55 kWh
55 l
1:37 h
Do not reach into the drum if it is still rotating.
Do not open the washing machine door if water can be seen through the glass.
/
.
3 kg
0.48 kWh
32 l
1:03 h
1.
Turn the programme selector to
2.
Drain the detergent solution -> page
(Delicates/
2 kg
0.06 kWh
31 l
0:41 h
3.
Pull the emergency release downwards with a tool and release.
Washing machine door can then be opened.
(Delicates/
2 kg
0.21 kWh
31 l
0:41 h
Information on the display panel
2 kg
0.10 kWh
39 l
0:40 h
2 kg
0.19kWh
39 l
0:40 h
F: 16
Close the washing machine door properly; laundry may be caught.
F: 17
Open the tap completely, supply hose kinked or trapped;
–> Page 10
Clean the filter
F: 18
Detergent solution pump blocked; Clean the detergent solution pump -> page
/
. (Quick/mixed fabrics) 40 °C
Drainage hose / waste pipe blocked; Clean the drainage hose at the siphon -> page
F: 21
Motor fault. Call customer services.
F: 23
Water in the base tub, appliance leaking. Call customer services.
8
– Risk of electric shock. Disconnect the mains plug.
Maintenance
– Risk of explosion. No solvents.
Detergent solution pump
Turn the programme selector to
.
(Off) and disconnect the mains
plug.
1. Open and remove the service flap.
(Easy-care) 60 °C and select
(Start/Reload). At the
. (Off).
2. For models with a drainage hose: Remove the drainage hose from
the retainer and pull it from the housing.Remove the container.
Remove the sealing cap, allow the detergent solution to flow out.
Replace the sealing cap and place the drainage hose in the retainer.
2* For models without a drainage hose: Carefully unscrew the pump cover
until the detergent solution begins to flow out.When the service flap is
half full, close the pump cover and empty the service flap. Repeat the
above steps until all the detergent solution has completely drained out.
3. Carefully unscrew the pump cover (residual water).
4. Clean the interior, pump cover thread and pump housing (the impeller in
the detergent solution pump must rotate).
5. Replace the pump cover and screw it tightly.
6. Place the service flap back on and close.
To prevent unused detergent from flowing straight into the drain during the next wash: Pour
1 litre of water into compartment II and start the
Drainage hose at the siphon
Turn the programme selector to
. (Off) and disconnect the mains plug.
Ensure there is no laundry in the machine
1. Loosen the hose clamp, carefully remove the drainage hose (residual water).
2. Clean the drainage hose and siphon connecting piece.
3. Reattach the drainage hose and secure the connection with the hose clamp.
Filter in the water supply
Risk of electric shock
Do not immerse the HydroSafe safety device in water (contains an electric valve).
Reduce the water pressure in the supply hose:
1. Turn off the tap.
. (Off) and disconnect the mains plug.
2. Select any programme (apart from
10
.
3. Choose
(Start/Reload). Let the programme run for approximately 40
seconds.
4. Turn the programme selector to
. (Off). Disconnect the mains plug.
Clean the filter:
1. Depending on model:
depending on model
Disconnect the hose from the tap.
Clean the filter using a small brush.
and/or for Standard and Aqua-Secure models:
, Water pressure too low.
Remove the hose on the rear of the appliance,
10
.
Remove the filter with pliers and clean.
10
.
2. Connect the hose and check for leaks.
9
– Risk of scalding.
Allow the detergent solution to cool
What to do if ...
down.
Water is leaking out.
– Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
No water supply.
–
(Start/Reload)
Detergent not dispensed.
not selected?
– Tap not turned on?
– Filter blocked? Clean the filter -> page
– Supply hose kinked or trapped?
Washing machine door
– Safety function active. Programme stopped? -> page
cannot be opened.
–
(Rinse Hold =
– Can be opened by emergency release only?
Programme does not start. –
(Start/Reload) or
(Finished in) time selected?
– Washing machine door closed?
– Childproof lock active? Deactivate -> page
Detergent solution is not
–
(Rinse Hold =
drained.
– Clean the detergent solution pump -> page
– Clean the waste pipe and/or drainage hose.
Water not visible in the
– Not a fault - water below the visible area.
drum.
Unsatisfactory spin result.
– Not a fault - the unbalanced-load detection system has cancelled the
Laundry wet/too damp.
spin cycle because of uneven distribution of the laundry.
Distribute small and large items of laundry evenly inside the drum
–
(Easy-iron)
selected? –> page 5.
– Selected speed too low? –> page 5.
The programme length
– Not a fault - the number of spin cycles may be changed due to the
jumps during the final spin..
varying distribution of the laundry, which may cause the time in the
display panel to be corrected.
(Drain) programme.
Spin cycle performed
– Not a fault - unbalanced load detection system adjusts the imbalance.
several times.
Residual water in the
– Not a fault - the action of the care product is not affected.
compartment for care
– Clean the insert if necessary -> page
products.
Odour formation in the
– Run programme
(Cottons) 90 °C without laundry. Use
washing machine.
standard detergent.
Status display
flashing.
– Too much detergent used?
Appliance has detected a
If foam is escaping from the detergent drawer:
detergent overload.
Mix 1 tablespoon of fabric softener with ½ litre of water and pour into
compartment
II
(not with outdoor or down fabrics).
– Reduce the detergent dosage for the next wash cycle.
Intense noise formation,
– Are the appliance feet fixed?
vibrations and "wandering"
Secure the appliance feet
–> Installation instructions
during the spin cycle.
– Transportation safety devices removed?
Remove the transportation safety devices –> Installation instructions.
n (Spin) /
(Drain)).
Display panel/indicator
– Power cut?
lamps do not function
– Fuses triggered? Reset/change the fuse.
during operation.
– If the fault occurs repeatedly, call customer services.
Programme sequence
– Not a fault - unbalanced load detection system adjusts imbalance by
longer than usual.
repeatedly distributing the laundry.
– Not a fault - foam detection system active - adds an additional rinse
cycle.
Detergent residues on the
– Occasionally, phosphate-free detergents contain water-insoluble
laundry.
residues.
– Use the
(rinse) cycle or brush out the laundry after
washing.
If you cannot correct a fault yourself or a repair is required:
– Turn the programme selector to
.
(Off) and remove the mains plug from the socket.
– Turn off the water supply and call customer services –> Installation instructions.
10
10
.
4
.
) selected?
->
page 3, 4.
->
page 9.
5
.
) selected?
-> page 3, 4.
10
.
Washing machine
9
.
Instruction manual
.
Observe the safety instructions on page 8.
Read these instructions and the separate installation instructions before
operating the washing machine.
11
en