Draper Silhouette V series Petunjuk Instalasi dan Pengoperasian
Jelajahi secara online atau unduh pdf Petunjuk Instalasi dan Pengoperasian untuk Layar Proyeksi Draper Silhouette V series. Draper Silhouette V series 4 halaman. Electric projection screen
Halaman Cetak
Silhouette/Series E & V Electric Projection Screen by Draper
➀ Read instructions through completely before proceeding; keep them for
future reference. Follow instructions carefully. Installation contrary to
instructions invalidates warranty. Care in mounting and correct oper-
ation will mean long and satisfactory service from your Draper screen.
➁ Screen should be accessible for complete removal should fabric
become damaged or should other service be required.
➂ Screen should be installed level (using a carpenter's level).
➃ Nothing should be fastened to screen dowel or viewing surface
➄ Operating switch(es) packed separately in screen carton. Do not
discard with packing material.
➅ Screen operates on 110-120v, 60 hz. current.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
These instructions are meant as a guide only. They do not imply
any responsibility on the part of Draper, Inc. for improper
installation or faulty workmanship at the jobsite.
Installation
Your Draper screen can be mounted on a wall or suspended from the
ceiling, or mounted on special 6" or 12" extension brackets. Extension
brackets must be ordered separately from Draper . With each method of
installation, the case must be mounted level and with the flat back parallel
to the wall.
To reduce the risk of personal injury, use only the hardware which comes
with the screen or is specified in these instructions.
The screen (or extension brackets) should be mounted into studs or
blocking in the wall/ceiling, or in drywall (minimum thickness
specified anchors. For any other type of installation, follow all local building
and safety codes.
Steel studs, concrete or cinder block walls and all other types of non-wood
frame construction require the use of special screws or anchors. The
selection of appropriate mounting hardware should be made by a qualified
professional installer.
When locating viewing surface and checking clearance for screen's
operation, remember surface is centered in case.
Take care to install wall/ceiling electrical box and conduit so they will be fully
concealed by the screen case after installation.
Handle case carefully to avoid scratching.
Regardless of mounting method, screen should be positively and securely
supported so that vibration or even abusive pulling on the viewing surface
will not cause case to work loose or fall. Installer must insure that fasteners
used are of adequate strength and suitable for the mounting surface
chosen.
Wall Mounting
Mount 2, 3, or 4 aluminum brackets provided ("Z" Clips) on the wall at
desired height, using appropriate fasteners. Verify that they are in line and
level to fully engage with the mounting lip on back of screen case. 1
free space is required above the "Z" Clips to allow case lip to be engaged
over the lip of the "Z" Clips.
Engage the lip on back of screen case with lip of "Z" Clip and gently pull
down to fully engage case to brackets.
Copyright © 2002 Draper Inc.
Installation/Operating Instructions
Caution
1
/
") with
2
Form SilhouetteE&V_Inst02
Lip on back of case
Locate 2 offset ceiling brackets (supplied) and slide these into the channel
on top of screen case by angling one side of bracket under lip of channel
and opposite side of bracket above notch in opposite channel lip.
Allow bracket to drop against bottom of channel and then slide it along case
until it stops against end cap of case. Tighten 2 set screws to lock bracket in
place. Make sure that the flange of the ceiling bracket that has 4 holes is
extended beyond the end caps of the case. Repeat above procedure for
second ceiling bracket, making sure to slide it towards opposite end of
case.
To mount against ceiling, hold screen case against ceiling and mark
mounting hole locations. Each bracket has 2 holes towards the front edge
and 2 holes towards the back edge. Installer must use at least 2 fasteners
per bracket with one fastener in one of the two holes closest to back edge of
bracket, and one fastener in one of the two hole closest to front edge of
bracket. Installer must insure that fasteners are of adequate strength and
5
/
" of
suitable for the mounting surface chosen.
8
(front of Silhouette case)
Printed in U.S.A.
Silhouette fully engaged
on "Z" Clip
"Z" Clip
(wall mounting bracket
supplied with Silhouette)
Ceiling/Suspended Mounting
Ceiling bracket in
channel of case
Ceiling bracket
Mounting fasteners
(supplied by others, 2 per bracket)
(right end of Silhouette case)