AirStage ASUA9RLAV Panduan Instalasi - Halaman 10

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Pendingin Udara AirStage ASUA9RLAV. AirStage ASUA9RLAV 15 halaman. Indoor unit (wall mounted type)

Halaman Cetak
Setting
Setting
range
Remote controller
0–15
address
Example If 4 indoor units are connected.
Indoor unit
Indoor unit
RC AD SW
RC AD SW
0
1
Remote
controller
RC AD SW
0
1
Address
0
1
RC AD SW
8
9
Address
8
9

6.2. Custom code setting

Selecting the custom code prevents the indoor unit mix-up.
(Up to 4 codes can be set.)
Perform the setting for both the indoor unit and the remote controller.
Confusion
Indoor
unit
Remote
controller
• Custom code setting for indoor unit
Set the DIP SW SET 3 SW1, SW2 referring to the Table B.
ON
OFF
Dip switch
"SET 3"
Table B
A (Factory setting)
DIP SW SET 3 SW1
DIP SW SET 3 SW2

6.3. Function Setting

• FUNCTION SETTING can be performed with the wired or wireless remote controller.
(The remote controller is optional equipment)
• Refer to the wired or wireless remote controller manual for detailed setting information.
(Set IU AD, REF AD SW to 0)
• Refer to "6.1. Setting the address." for indoor unit address and refrigerant circuit ad-
dress settings.
• Turn the power of the indoor unit ON before starting the setting.
* Turning on the power to the indoor units initializes EEV, so make sure the piping air
tight test and vacuuming have been conducted before turning on the power.
* Also check again to make sure no wiring mistakes were made before turning on the
power.
En-9
Type of switch
Setting
example
0
RC-AD
Indoor unit
Indoor unit
RC AD SW
RC AD SW
2
3
2
3
4
5
2
3
4
5
A
B
C
D
10
11
12
13
Code change
A
B
C
D
A
B
C
D
Custom code
B
C
OFF
ON
OFF
OFF
OFF
ON
Function details
Function
Function
number
Filter
indicator
11
interval
Filter indi-
13
cator action
Cool air
tempera-
30
ture trigger
6
7
6
7
Heat air
tempera-
31
E
F
ture trigger
14
15
Auto restart
40
External
46
control
Error report
47
target
6.3.1 Button name and function
D
ON
ON
OPERATION indicator lamp (Green)
6.3.2 Checking the function settings
Press and hold the "MANUAL AUTO" button on the indoor unit for 3 seconds to check the
function settings. It is necessary to disconnect the power in order to return to normal op-
eration mode.
Setting number Default
○
00
Default
Adjust the fi lter cleaning interval notifi ca-
tion. If the notifi cation is too early, change
01
Longer
to setting 01. If the notifi cation is too late,
change to setting 02.
02
Shorter
○
00
Enable
01
Disable
Enable or disable the fi lter indicator.
Setting 02 is for use with a central
Display only
remote controller.
on central
02
remote
controller
○
00
Default
Adjust the cool air trigger temperature. To
lower the trigger temperature, use setting
01
Adjust (1)
01. To raise the trigger temperature, use
setting 02.
02
Adjust (2)
○
00
Default
Adjust the heat air trigger temperature. To
lower the trigger temperature by 11 degrees F
01
Adjust (1)
(6 degrees C), use setting 01. To lower the
trigger temperature by 7 degrees F
02
Adjust (2)
(4 degrees C), use setting 02. To raise the
trigger temperature, use setting 03.
03
Adjust (3)
00
Enable
Enable or disable automatic
system restart after a power
○
01
Disable
outage.
○
Allow an external controller to start or stop
00
Start/Stop
the system, or to perform an emergency stop.
Emergency
* If an emergency stop is performed from an
01
stop
external controller, all refrigerant systems
will be disabled.
* If forced stop is set, indoor unit stops by
Forced
the input to the external input terminals,
02
stop
and Start/Stop by a remote controller is
restricted.
○
00
All
Change the target for reporting errors. Er-
Display only
rors can either be reported in all locations,
on central
01
or only on the wired remote.
remote
controller
FILTER indicator lamp (Red)
TIMER indicator lamp (Orange)
Details