Draper 56405 Manual - Halaman 7

Jelajahi secara online atau unduh pdf Manual untuk Bor Draper 56405. Draper 56405 20 halaman. 230v 5.2kg sds+ rotary hammer drill

Halaman Cetak

BASIC HAMMER DRILL OPERATIONS

HEALTH AND SAFETY INFORMATION

9.7 SDS+ SYSTEM – FIGS.13 – 14

Remove and check setting tools. Some machinery requires the use of additional tools or keys to set,

load or adjust the power tool. Before starting the power tool always check to make certain they have

The tool holder (1.2) clamps SDS+ drill bits and

been removed and are safely away from the machine.

chisels without the need for a chuck key.

Prevent unintentional starting. Before plugging any machine in to the power supply, make sure the

– Pull collar (1.3) back.

switch is in the OFF position. If the machine is portable, do not hold the machine near the switch and

– Insert the bit. It may be necessary to rotate the

take care when putting the machine down, that nothing can operate the switch.

bit to ensure it engages correctly.

Carefully select an extension lead. Some machines are not suitable for use with extension leads. If

– Release the collar to lock the bit in place. Check

the tool is designed for use outdoors, use an extension lead also suitable for that environment. When

by pulling the bit to see if it's firmly seated.

using an extended lead, select one capable of handling the current (amps) drawn by the machine in

Important: Always clean and lightly grease the tool

use. Fully extend the lead regardless of the distance between the power supply and the tool. Excess

shaft before inserting into the chuck.

current (amps) and a coiled extension lead will both cause the cable to heat up and can result in fire.

Take care that the dust protection cap is not

Concentrate and stay alert. Distractions are likely to cause an accident. Never operate a power tool if

damaged. Allowing dust and debris inside the

you are under the influence of drugs (prescription or otherwise), including alcohol or if you are feeling

holder will cause problems in the future.

tired. Being disorientated will result in an accident.

– To remove a bit, slide the collar (1.3) to the rear

Have this tool repaired by a qualified person. This tool is designed to conform to the relevant

and pull out the tool.

international and local standards and as such should be maintained and repaired by someone

Warning! Bit will be hot after use.

qualified, using only original parts supplied by the manufacturer. This will ensure the tool remains safe

to use.

9.8 DUST AND SWARF:

5.2 ADDITIONAL SAFETY INSTRUCTIONS FOR HAMMER DRILLS

A correctly fitted dusk mask, suitable for the activity

and in accordance to the relevant standard, must be

Important: Draper Tools Limited recommends that this machine should not be modified or used

worn.

for any application other than that for which it was designed. If you are unsure of its relative

applications do not hesitate to contact us in writing and we will advise you.

For work activities involving exposure to fine wood

dust, a mask rated to at least FFP2 should be used.

– Power tools shall not be used in potentially explosive atmospheres unless specifically designed

for that purpose.

Swarf produced by metal drilling is extremely sharp.

Take precautions when clearing swarf. The burr left

– Unexpected tool movement due to reaction forces or breakage may cause injuries.

on the hole is also sharp and should be removed

– Power tools shall be isolated from the energy source before changing or adjusting the inserted

with a suitable tool.

tool.

9.9 DRILLING WOOD, PLASTIC OR METAL

Warning!

● Wear appropriate ear protection. Exposure to noise can lead to hearing loss.

Although technically possible, Draper Tools do not recommend the use of this machine for drilling

into wood, metal or plastic. This machine is designed for drilling through brick, concrete and is

● There is a risk of loose clothing, hair etc., being caught in the rotating spindle of the

engineered to do so. This makes it an unwieldy machine to drill wood, metal or plastic and there

power tool.

are tools that are far more capable of doing the job with a greater degree of control.

● Do not touch the drill bit or areas close to the drill bit immediately after use; they can still

be extremely hot, causing burns.

– Be sure the drill bit is securely in place before using the drill.

– There is a risk of release of toxic chemicals into the atmosphere when using certain materials.

Always be mindful to use the appropriate personal protective wear to help safeguard against

potential skin contact and dust inhalation. Always consult and follow the material supplier's

safety guidelines.

– Adopt a suitable posture to counteract normal or unexpected movement of the power tool due

to reaction forces from the power assembly tool.

– Do not modify this product in any way. Any other application is considered misuse and will

invalidate the warranty.

(1.2)

FIG.13

FIG.14

- 15 -

- 7 -

(1.3)

(1.2)

(3)

(1.3)