AirStage ASYE007GTAH Panduan Instalasi - Halaman 10

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Pendingin Udara AirStage ASYE007GTAH. AirStage ASYE007GTAH 15 halaman. Indoor unit (floor type)
Juga untuk AirStage ASYE007GTAH: Panduan Pengoperasian (8 halaman)

Halaman Cetak

6.3. Function setting

Please make this setting after completing all construction works.

• FUNCTION SETTING can be performed with the wired or wireless remote controller.

(The remote controller is optional equipment)

• Refer to the wired or wireless remote controller manual for detailed setting information.

• Refer to "6.1. Setting the address" for indoor unit address and refrigerant circuit address

settings.

• Turn the power of the indoor unit ON before starting the setting.

* Turning on the power to the indoor units initializes EEV, so make sure the piping air tight

test and vacuuming have been conducted before turning on the power.

* Also check again to make sure no wiring mistakes were made before turning on the

power.

Function details

Function

Setting number

number

00 Standard

Filter

indicator

01 Longer

interval

02 Shorter

00 Enable

01 Disable

Filter

indicator

Display only

action

on central

remote

controller

(Forbidden)

00 Standard

Horizontal

swing

01 Left half

airflow

direction

02 Right half

00 Standard

Cool air

tempera-

01 Adjust (1)

ture trigger

02 Adjust (2)

00 Standard

Heat air

01 Adjust (1)

tempera-

02 Adjust (2)

ture trigger

03 Adjust (3)

00 Enable

Auto restart

01 Disable

00 Super low

Cool Air

Follow the

Prevention

setting on

the remote

controller

00 Start/Stop

External

Emergency

control

stop

02 Forced Stop

En-9

WARNING

Default

Details

○

Adjust the filter cleaning interval

notification. If the notification is too

early, change to setting 01. If the

notification is too late, change to

setting 02.

○

Enable or disable the filter indica-

tor. Setting 02 is for use with a

central remote controller.

○

Adjust the horizontal swing airflow

direction.

(For horizontal swing equipped

models)

○

Adjust the cool air trigger tempera-

ture. To lower the trigger tempera-

ture, use setting 01. To raise the

trigger temperature, use setting 02.

○

Adjust the heat air trigger

temperature. To lower the trigger

temperature by 6 degrees C, use

setting 01. To lower the trigger

temperature by 4 degrees C, use

setting 02. To raise the trigger

temperature, use setting 03.

Enable or disable automatic system

restart after a power outage.

* Auto restart is an emergency func-

tion such as for power failure etc.

Do not start and stop the indoor

○

unit by this function in normal

operation.

Be sure to operate by the control

unit, converter or external input

device.

○

Restrain the cold airflow with mak-

ing the airflow lower when starting

heating operation. To correspond to

○

the ventilation, set to 01.

Allow an external controller to start

○

or stop the system, or to perform

an emergency stop.

If an emergency stop is performed

from an external controller, all re-

frigerant systems will be disabled.

If forced stop is set, indoor unit

stops by the input to the external

input terminals, and Start/Stop by a

remote controller is restricted.

00 All

Display only

Error report

target

on central

remote

controller

Follow the

Fan setting

setting on

when

the remote

cooling

controller

thermostat

OFF

01 Stop

(Forbidden)

Single set-

point auto

mode

Auto mode

(traditional)

type

Dual set-

point auto

mode

00 0°C

01 0.5°C

02 1.0°C

03 1.5°C

04 2.0°C

Deadband

value

05 2.5°C

06 3.0°C

07 3.5°C

08 4.0°C

09 4.5°C

6.3.1 Indoor unit indicator lamps

004/007/009 model

OPERATION indicator lamp (green)

TIMER indicator lamp (orange)

FILTER indicator lamp (red)

030/034 model

OPERATION indicator lamp (green)

TIMER indicator lamp (orange)

FILTER indicator lamp (red)

○

Change the target for reporting er-

rors. Errors can either be reported

in all locations, or only on the

central remote controller.

When set to 01, the fan stops when

○

the thermostat is OFF in cooling

operation. Connection of the wired

remote controller (2-wire type

or 3-wire type) and switching its

thermistor are necessary.

○

Switch the setting method of

○

auto mode to single or dual

(cooling/heating).

For heat pump systems, it is

necessary to set the master indoor

unit (by wired remote controller).

Choose the minimum temperature

between cooling and heating

settings (deadband) for Dual

setpoint auto mode (set in No. 68).