Drawmer CPA-50 Panduan Operator - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Operator untuk Penguat Drawmer CPA-50. Drawmer CPA-50 12 halaman.

Halaman Cetak

DRAWMER

laws, no part of this publication may be reproduced, transmitted, stored in a retrieval system or translated

into any language in any form by any means, mechanical, optical, electronic, recording, or otherwise,

without the written permission of Drawmer Electronics Ltd.

Drawmer Electronics Ltd., warrants the Drawmer CPA-50 Power

Amplifier to conform substantially to the specifications of this manual

for a period of one year from the original date of purchase when used

in accordance with the specifications detailed in this manual. In the

case of a valid warranty claim, your sole and exclusive remedy and

Drawmer's entire liability under any theory of liability will be to, at

Drawmer's discretion, repair or replace the product without charge,

or, if not possible, to refund the purchase price to you. This warranty

is not transferable. It applies only to the original purchaser of the

product.

For warranty service please call your local Drawmer dealer.

Alternatively call Drawmer Electronics Ltd. at +44 (0)1709 527574.

Then ship the defective product, with transportation and insurance

charges pre-paid, to Drawmer Electronics Ltd., Coleman Street,

Parkgate, Rotherham, S62 6EL UK. Write the RA number in large

letters in a prominent position on the shipping box. Enclose your

name, address, telephone number, copy of the original sales invoice

and a detailed description of the problem. Drawmer will not accept

responsibility for loss or damage during transit.

This warranty is void if the product has been damaged by misuse,

modification, unauthorised repair or installed with other equipment

that proved to be faulty.

THIS WARRANTY IS IN LIEU OF ALL W ARRANTIES, WHETHER

ORAL OR WRITTEN, EXPRESSED, IMPLIED OR STATUTORY.

DRAW MER MAKES NO OTHER W ARRANTY EITHER

EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION,

ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS

FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT.

PURCHASER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS

WARRANTY SHALL BE REPAIR OR REPLACEMENT AS

SPECIFIED HEREIN.

IN NO EVENT WILL DRAWMER ELECTRONICS LTD. BE LIABLE

FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES RESULTING FROM ANY

DEFECT IN THE PRODUCT, INCLUDING LOST PROFITS,

DAMAGE TO PROPERTY, AND, TO THE EXTENT PERMITTED

BY LAW, DAMAGE FOR PERSONAL INJURY, EVEN IF

DRAWMER HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

Some states and specific countries do not allow the exclusion of

implied warranties or limitations on how long an implied warranty may

last, so the above limitations may not apply to you. This warranty gives

you specific legal rights. You may have additional rights that vary from

state to state, and country to country.

In the interests of product development, Drawmer reserve the right to modify

or improve specifications of this product at any time, without prior notice.

DO NOT OPEN. REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL.

TO REDUCE RISK OF FIRE/ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT TO MOISTURE.

DO NOT ATTEMPT TO CHANGE OR TAMPER W ITH THE SUPPLIED MAINS CABLES.

THE FUSE IN THE INLET HAS BEEN SET TO A RATING THAT ENSURES IT WILL BLOW BEFORE THE

INTERNAL FUSE IF THE AMPLIFIER IS DRIVEN AT CLIPPING LEVELS FOR ANY SIGNIFICANT LENGTH

OF TIME. THIS IS TO PREVENT THE AMPLIFIER AND/OR SPEAKERS FROM BEING DAMAGED. TO

REDUCE THE RISK OF FIRE REPLACE THE MAINS FUSES ONLY WITH A FUSE THAT CONFORMS TO

IEC127-2. 250 VOLT WORKING, TIME DELAY TYPE AND BODY SIZE OF 20mm x 5mm. THE MAINS

INPUT FUSE MUST BE RATED AT T800mA at 115V and T500mA at 230V.

ONE YEAR LIMITED WARRANTY

SAFETY CONSIDERATIONS

CAUTION - SERVICING

WARNING

For the USA

FEDERAL COMMUNICATIONS COMMISSION RADIO

FREQUENCY INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause interference to radio or television

reception, which can be determined by turning the equipment off an

on, then the user is encouraged to try to correct the interference by

one or more of the following measures:

Re-orient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Unauthorised changes or modification to this system can void the

users' authority to operate this equipment.

This equipment requires shielded interface cables in order to meet

FCC class B limit.

For Canada

CLASS B

This digital apparatus does not exceed the Class B limits for radio

noise emissions set out in the Radio Interference Regulations of the

Canadian Department of Communications.

CLASSE B

Cet appareil numérique ne dépasse pas les limites de la classe B au

niveau des émissions de bruits radioélectriques fixés dans le

Règlement des signaux parasites par le ministère Canadien des

Communications.

NOTICE

AVIS