Alemlube 600A Panduan Pemilik

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Peralatan Alemlube 600A. Alemlube 600A 2 halaman. Lever action grease gun
Juga untuk Alemlube 600A: Petunjuk Servis (2 halaman), Panduan Teknis Pemilik (2 halaman)

Halaman Cetak

Description

The 600A manufactured in Germany, is a lever action 450g grease gun capable of generating up to 12,000 psi. It comes

standard with a 16.5cm rigid extension & 4 jaw coupler for lubricating points. It has a 600g bulk grease capacity & comes

with 4 year warranty. Furthermore, the patented Ever-Flow System enables the gun to be used even with most thick, tacky

greases up to NLGI3.

Specifications

Uses

Pressure Capabilities

Delivery

Operating Instructions

There are two ways to fill the gun with grease:

A: 450g Grease Cartridge:

Unscrew the grease barrel from the gun and insert the 450g grease

cartridge by holding the barrel assembly and pulling the rod back.

Remove cap from the grease cartridge, insert the cartridge into the barrel

and then rescrew the barrel assembly back onto the gun so that the cartridge

sits well against the follower cup. Once in position, press the clamp down

& push the rod firmly back into the barrel.

Important To Note:

When using the gun with a cartridge, the follower cup must be folded back.

The gun is supplied standard with the follower cup in this position.

B: Bulk Grease Loading:

Unscrew the grease barrel from the gun head & insert the barrel into the bulk

grease. Suck the grease up into the barrel by pulling the rod all the way back.

When barrel is full with grease, rescrew the barrel assembly back onto the gun

head so that the follower sits well against the grease. Press the clamp down

& push the rod firmly back into the barrel.

Important To Note:

When using the gun with bulk grease, the follower cup must be folded forward.

To do this, take the follower cup and rod assembly out of the barrel, fold the

follower cup forward and reassemble the barrel assembly.

Maintenance

Cleaning: always keep the follower cup free of impurities. Your grease should be clear

of any foreign particles, dirt etc and the gun should be checked and cleaned regularly.

Trouble Shooting

Air Pocked In Grease: If the gun is pumped but no grease appears from the coupler:

Depress the air bleeder valve on the head and pump a few strokes.

Unscrew the barrel assembly from the gun head with two or three turns and then push

on the plunger rod. With the follower cup engaged the follower cup will move further

down into the barrel venting any trapped air out through the thread connections between

the barrel and head. Unscrew the rigid extension as well.

Safety Warning

Always use safety goggles and gloves when operating this grease gun. Personal injury may occur

and if so seek immediate medical attention. Do not use a high pressure grease fitting as a loader fitting.

Excessive pressure can cause personal injury and equipment damage.

NSW/ACT

TEL: (02) 9677 1555

FAX: (02) 9675 1155

OWNER'S MANUAL

Lever Action Grease Gun

450g Grease Cartridges, Suction loading, Bulk loader pump from bulk grease drum.

Up to 12,000psi grease pressure

1.6cc per stroke

QLD/PNG

VIC/TAS

TEL: (07) 3204 9166

TEL: (03) 8787 8288

FAX: (07) 3204 1224

FAX: (03) 8787 8266

Visit our website at

www.alemlube.com.au

SA/NT

TEL: (08) 9302 4199

TEL: (08) 8241 7111

FAX: (08) 9303 2095

FAX: (08) 8241 7011

www.alemlube.co.nz

600A

June 2022

TEL: (09) 447 1007

FAX: (09) 447 1008