Bosch FAP-OC 500Series Panduan Servis - Halaman 21

Jelajahi secara online atau unduh pdf Panduan Servis untuk Oven Bosch FAP-OC 500Series. Bosch FAP-OC 500Series 36 halaman. Built-in wall ovens
Juga untuk Bosch FAP-OC 500Series: Panduan Petunjuk Instalasi (21 halaman), Petunjuk Penggunaan Manual (40 halaman), Panduan Instalasi (6 halaman), Informasi Produk (40 halaman), Panduan Instalasi (28 halaman), Panduan Pengguna (48 halaman), Panduan Pengguna (48 halaman), Panduan Instalasi (28 halaman), Panduan Penggunaan dan Perawatan (44 halaman), Panduan Instalasi (32 halaman), Panduan Penggunaan dan Perawatan / Petunjuk Pemasangan (40 halaman), Panduan Referensi Cepat (4 halaman), Panduan Penggunaan dan Perawatan (27 halaman), Panduan Instalasi (24 halaman), Panduan Instalasi (32 halaman), Panduan Penggunaan dan Perawatan (24 halaman), Panduan Instalasi (28 halaman), Panduan Servis (41 halaman), Panduan Penggunaan dan Perawatan (21 halaman), Panduan Instalasi (32 halaman), Panduan Instalasi (32 halaman), Panduan Memulai Cepat dan Keselamatan (13 halaman)

Bosch FAP-OC 500Series Panduan Servis
Figure 20 HBL3/HBN3 User interface
To set the option code...
5.
Locate the 4-digit code on the label near the PC Control
Board in the upper plenum or in Table 8 below.
6.
Press TEMP to advance to the Option Code (OC) screen.
7.
Press COOK TIME.
8.
Rotate the Settings dial to change the code.
To exit service mode...
9.
Rotate the Cooking Mode dial to the OFF position.
10.
Rotate the Settings dial to set the time.
To reset the oven...
11.
Unplug the unit or turn the power off at the circuit breaker for
30 seconds.
12.
Rotate the Settings dial to set the time.
5.2.2

HBL5/HBN5

To enter service mode...
1.
Press and hold START and FAST PREHEAT.
2.
Rotate the Cooking Mode dial out of the OFF position.
3.
Release the two buttons.
Figure 21 HBL5/HBN5 User interface
To set the option code...
4.
Locate the 4-digit code on the label near the PC Control
Board in the upper plenum or in Table 8 below.
5.
Set the Option Code by rotating the Settings dial.
To exit service mode...
6. Rotate the (upper oven) Cooking Mode dial to the OFF
position.
7. Rotate the Settings dial to set the time.
8. Press
and rotate the Settings dial to set the date. (See
Use and Care Manual for further information about setting time
and date.)
To reset the oven...
9. Unplug the unit or turn the power off at the circuit breaker for
30 seconds.
10. Set the current time and date (see 7 and 8 above).
5.2.3

HBL8

To enter service mode...
1.
Press and hold START.
2.
Press and hold FAST PREHEAT.
3.
Press ON/OFF.
4.
Release all three buttons.
E000
Wrong
Figure 22 HBL8 User interface
To set option code...
5.
Locate the 4-digit code on the label near the PC Control
Board in the upper plenum or in Table 8 below.
6.
Press FAST PREHEAT to advance to the Option Code
menu selection.
Service Manual for Bosch Built-in Wall Ovens
Page 21 of 36