Alemlube HR90000 Series Panduan Teknis Pemilik - Halaman 2
Jelajahi secara online atau unduh pdf Panduan Teknis Pemilik untuk Peralatan Alemlube HR90000 Series. Alemlube HR90000 Series 6 halaman. Spring rewind hose reels
Juga untuk Alemlube HR90000 Series: Panduan Teknis Pemilik (10 halaman), Panduan Teknis Pemilik (5 halaman)
Halaman Cetak
OWNER'S TECHNICAL MANUAL
GENERAL SAFETY REGULATIONS
WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions or situations that could occur. It must be understood by the operator
that common sense and caution are factors that cannot be built into this product, but must
be supplied by the operator.
1. Keep the work area clean and dry. Damp or wet work areas can result in injury.
2. Keep children away from work area. Do not allow children to handle this product.
3. Use the right tool for the job. Do not attempt to force small equipment to do the work of larger industrial
equipment. There are certain applications for which this equipment was designed. It will do the job better
and more safely at the capacity for which it was intended. Do not modify this equipment, and do not use this
equipment for a purpose for which it Was not intended.
4. Check for damaged parts. Before using this product, carefully check that it will operate properly and perform
its intended function. Check for damaged parts and any other conditions that may affect the operation of this
product. Replace damaged or worn parts immediately.
5. Do not overreach. Keep proper footing and balance at all times to prevent tripping, falling, back injury, etc.
6. Do not use the equipment when tired or under the influence of drugs, alcohol, or medication.
A moment of inattention while operating this equipment may result in serious personal injury.
SAFETY PRECAUTIONS
1. Make sure incoming line pressure does not exceed rated operating pressure for your model hose reel.
2. Use proper eye protection when assembling and using the hose reel.
3. Keep children away from the work area.
4. For long-time nonuse, please empty the hose
5. If long-term preservation of the hose reel, please check whether the hose is aging and whether the connecting
valve is leaking.
WARNING: Exposure of skin to pressurized air or fluid could result in severe injury.
INSTALLATION
For overhead ceiling and wall mounting: the installation height should not exceed 3m (10 feet) above the floor.
If the reel you have purchased does not have hose included, you will need to purchase and attach.
Refer to Specifications to determine appropriate hose and size.
1. The reel base has four 7/16" (11mm) drilled holes for mounting on a suitable flat surface.
The Mounting Template shows the correct location of the 4 mounting holes in the base.
2. The reel is supplied with a hose guide roller bracket. The bracket position may require repositioning depending
on the selected reel mounting position. If bracket position needs to be changed, do the following:
(1) Pull out some hose and let reel latch.
(2) Remove side cover and guide arm.
(3) Rotate guide roller bracket to correct position, replace bolts and tighten.
3. Using the four holes in the base, mount the reel in the desired location.
Be sure to use appropriate hardware and tighten securely.
4. Apply Teflon tape or pipe sealant to supply line threads, attach to reel inlet and tighten.
The other end of incoming line can now be connected to desired supply source.
5. If hose has been supplied with reel: Apply Teflon tape or pipe sealant to outlet fitting on reel hose, then
attach to desired tool, or nozzle. Check connection for leakage, also check hose reel for correct operation.
(Details see Operation section.)
6. If hose stopper adjustment is required, pull hose from reel and allow to latch at desired length. Loosen stopper
bolts and slide stopper to a position close to the hose guide. Tighten stopper bolts, and unlatch the reel.
NSW/ACT
QLD/PNG
TEL: (02) 9677 1555
TEL: (07) 3204 9166
FAX: (02) 9675 1155
FAX: (07) 3204 1224
Dual Pedestal Spring Rewind Hose Reels
VIC/TAS
TEL: (03) 8787 8288
FAX: (03) 8787 8266
Visit our website at
www.alemlube.com.au
WA
SA/NT
TEL: (08) 9302 4199
TEL: (08) 8241 7111
FAX: (08) 9303 2095
FAX: (08) 8241 7011
or
www.alemlube.co.nz
HR90000
Series
NZ
TEL: (09) 447 1007
FAX: (09) 447 1008
2