Alemlube HR90065 Panduan Teknis Pemilik - Halaman 7
Jelajahi secara online atau unduh pdf Panduan Teknis Pemilik untuk Peralatan Alemlube HR90065. Alemlube HR90065 10 halaman. Spring rewind hose reel
Operational Instructions for HR90000 Series
Industrial Hose Reel 286X Series Instruction
Operation
1. Check reel for correct operation by slowly pulling out the hose. A "clicking" noise will be
heard every half revolution of the drum.
2. To latch the reel, pull out the hose and allow it to retract after hearing the first second or third
" click".
3. To unlatch, slowly pull out the hose until the "clicking" noise stops, then let the hose retract
until the hose stop rests against the hose guide. Note: To avoid damage to the reel, always
hold on to the hose while it is rewinding.
4. Periodically check the hose condition for wear or damage, and check the swivel fitting for
leakage. Replace any worn, damaged, or leaking parts.
Adjustment of Spring Tension
1. Pull out approximately 6ft or 2m of hose and allow the drum to latch.
2. Remove hose stopper from hose, and feed hose back through guide.
3. Wrap the pulled hose one time around the drum to increase tension or un-wrap hose one
time from drum to decrease tension.
4. Re-insert hose through guide, and install stopper onto hose end.
5. Unlatch the Drum and check tension. Pull hose from reel, and adjust stopper position if
necessary.
Replacement of Hose
1. Turn off supply to reel.
2. Pull out all the old hose and lock the reel in this position. Caution: Make sure reel drum is
securely locked and cannot rotate back.
3. Remove two hose clamps from hose.
4. Carefully disconnect hose from swivel joint on side of reel, or male fitting in axle center and
remove old hose.
5. Feed new hose through guide and opening in drum, and connect to swivel. Re-install two
hose clamps, on inside and outside of drum flange. Install stopper on other end of hose in the
same position as before.
6. Carefully release the drum latch, and slowly allow the hose to wind onto the reel. Note: Final
spring adjustment is accomplished by adding or removing wraps of hose around the drum.
(Details see spring tension adjustment).
Spring Canister Warning
If the rewind spring fails for any reason: For safety reasons, the manufacturer strongly
recommends the replacement of the spring canister be carried out by a professional mechanic.
Limited Warranty
1. The manufacturer warrantees this hose reel against defects in material and craftsmanship, for
a period of 12 months from date of purchase.
2. Hose, if supplied with reel, O-rings, plastic rollers and rubber stopper are deemed to be
normal wear items; not warranted.
3. Manufacturer's liability is limited to replacement or repair of defective material within the
warranty period, when returned freight prepaid to the distributor or their designated service
depot.
4. The warranty does not cover damage caused by accident, misuse or faulty installation.
5. The reel must be installed and maintained in compliance with the instructions.
NSW
QLD / PNG
TEL: (02) 9677 1555
TEL: (07) 3204 9166
FAX: (02) 9675 1155
FAX: (07) 3204 1224
Visit our website at
6 OF 9
VIC / TAS
WA
TEL: (03) 8787 8288
TEL: (08) 9302 4199
FAX: (03) 8787 8266
FAX: (08) 9303 2095
www.alemlube.com.au
SA / NT
TEL: (08) 8241 7111
FAX: (08) 8241 7011
or
www.alemlube.co.nz
NZ
TEL: (64) 9 447 1007
FAX: (64) 9 447 1008
7