Carlin 60200FR Panduan Petunjuk Pemasangan dan Pengoperasian - Halaman 7
Jelajahi secara online atau unduh pdf Panduan Petunjuk Pemasangan dan Pengoperasian untuk Pengontrol Carlin 60200FR. Carlin 60200FR 9 halaman. Gas burner primary control
Juga untuk Carlin 60200FR: Panduan Petunjuk Pemasangan dan Pengoperasian (8 halaman)
Halaman Cetak
Fault History
The 60200FR stores information from the last 32 cycles in
which a fault condition occurred. To Enter the Fault History
, simultaneously press and hold the
seconds. The display below will appear –
View 13 Faults
To Exit Hold
E
Press the
button to scroll through the history of fault
conditions. Fault 1 is the most recent cycle in which a fault
occurred. To view faults experienced in earlier run cycles,
continue to press the
E
button. The control will display Fault
2 followed by Fault 3, etc.
Fault 1 Details
View Fault 2
To view the details of any fault (ex. Fault 1 in the screen
H
above), press the
button to see the Fault Message.
Fault 1 Message
No Flame Check Vlv
H
Press the
button again to determine how many cycles ago
the fault occurred.
Fault 1
X X X X cycles ago
H
Press the
button again to determine if the fault resulted in a
lockout or a recycle.
Fault 1 Result
Lockout
H
Press the
button again to examine the Microamps at the
time of the fault.
Fault 1
0.1 uAmps
F A U L T
H I S T O R Y
NOTE: Fault information in chart
is representation only.
Carlin Combustion Technology, Inc.
H
E
and
buttons for 2
PRESS THE
Message
PRESS THE
Cycles Ago
Result
µAmps
BUTTONS
Line Volts
TO
VIEW
Motor Amps
FAULT
Ignitor Amps
DETAILS
Valve Amps
Recycle Y/N
Burn Time
Flame Delay
Continue pressing the
information recorded during the fault cycle.
• Line Voltage
• Motor Amps (OK or Low)
• Ignitor Amps (OK or Low)
• Valve Amps (OK or Low)
On any fault detail screen listed above, the
pressed to view the same data in the previous fault cycle. For
example, if in Fault 1 (the most recent fault), the Ignitor Amps
were low, by pressing the
2 (the previous fault cycle) will be displayed.
Fault 1
Ignitor Amps Low
To Exit Fault History: Press and hold the
ton for 3 seconds at any time.
Total/Run History
In addition to the Fault History (left),the 60200FR also logs the
total run history of the control. To enter this menu, simultane-
E
ously press the
below will appear.
Total History
To Exit Hold
To Exit Total History: Press and hold the
ton for 3 seconds at any time.
H
Press
button to scroll through the history which includes:
• Total On Time
• Total Burn Time
• Total Burner Run Cycles
• Faults Cleared (cycles ago)
BUTTON TO VIEW NEXT FAULT
FAULT 1
FAULT 2
No Flame ck vlv
No Flame ck MTR
2
3
Lockout
Lockout
0.1
0.1
114
114
OK
Low
OK
OK
Low
OK
No
No
5 sec
5 sec
4 sec
4 sec
7
H
button to examine the following
• Recycle (Yes or No)
• Burn Time
• Flame Delay
E
button can be
E
button, the Ignitor Amps in Fault
Fault 2
Ignitor Amps OK
F
/ ESCAPE but-
F
buttons for 3 seconds. The display
and
/ ESCAPE but-
• Max Line Volts
• Min Line Volts
• Total Recycles
FAULT 3
FAULT 4
No Flame ck IGN
No Flame ck vlv
4
5
Lockout
Lockout
0.1
0.1
114
114
OK
OK
Low
OK
OK
Low
No
No
5 sec
5 sec
4 sec
4 sec
MN60200FR1 070319
FAULT 5
No Flame ck vlv
6
Lockout
0.1
114
OK
OK
Low
No
5 sec
4 sec