Alemlube 51008P Panduan Teknis Pemilik

Jelajahi secara online atau unduh pdf Panduan Teknis Pemilik untuk Alat Ukur Alemlube 51008P. Alemlube 51008P 2 halaman. Mechanical petrol meter

Halaman Cetak

Description

The 51008P mechanical petrol meter has an aluminium body incorporating an inlet and outlet flange and can meter petrol accurately

between 15 and 120 L/min. Featuring an oscillating plate, the meter incorporates bypasses which enable the meter to be used on

petrol of varying viscosity's. The meter features rotational inlet/outlet for vertical or horizontal applications. The meter includes a set

of resetable digits that need to be reset to zero before the meter is to be used to record its next batch reading. The meter can be

supplied with a 1"BSP (f) filter, an optional extra (Part No. 51008F) or without the filter (Part No. 51008P.)

Specifications

Suitable for

Flow rate

Maximum Pressure

Weight

Inlet/Outlet connections 1" BSP (F)

Operating Instructions

1 Configure the meter in an orientation that suits your application i.e.: by

undoing screws at the base of the meter and reorientate the meter so that

the inlet and outlet of the meter suit your application.

2 Connect the meter inlet to the hose or fixed fitting that the product is being

delivered through.

3 Once threads connected and completely sealed with thread tape, open the

tanks on/off valve or start up the pump.

4 Petrol will now start to flow through to the mechanical flow meter turning

over the batch recording digits and totaliser recording digits

Important To Note:

The 51008 and 51008F fuel meters are pre-calibrated in factory to be used

with petrol fuel. As specific operating conditions (such as real flow rate,

the viscosity and temperature of the measured fluid) may affect the meter

accuracy, a recalibration should be carried out after the installation has

been completed. A new calibration is necessary each time the meter is

disassembled for maintenance operations or when it is used to measure

fluids that differ from petrol fuel.

Calibration Procedure

1 Unscrew the plug (Part No. 51008-4)

2 Purge the system (pump, pipelines, meter) of air by dispensing until the

flow of petrol is full and steady.

3 Stop the flow by shutting off the nozzle, but keep the pump running.

4 Reset the batch register by means of the reset know

(Part No. 51008-2).

5 Dispense at the flow rate which the best accuracy is required at, by using

a calibration container having a capacity not less than 20L. Do not reduce

the flow in order to reach the graduated zone of the calibration container.

The right way to do this is to start and stop the flow rate repeatedly until the

required filling is obtained.

Compare the indication of the calibration with the one of the meter. If the

indicated value is higher than the real value, loosen the screw

(Part No.51008-13) if the indicated value is lower than the real value,

tighten the screw (Part No. 51008-13).

7 Repeat the operations 4 to 6 until accuracy is satisfactory.

8 Tighten the plug (Part No. 51008-14) again. The O'Ring (Part No. 51008-11) which the calibration screw is

provided with has the function to avoid accidental loosening of the adjustment screw but does not facilitate

any sealing function.

NSW

QLD/PNG

TEL: (02) 9939 0711

TEL: (07) 3204 9166

FAX: (02) 9939 0411

FAX: (07) 3204 1224

Visit our website at

OWNER'S TECHNICAL MANUAL

Mechanical Petrol Meter

Measuring the transfer of petrol

20 L/min to 120 L/min

3 bar (50psi)

2.0kg

Accuracy-+1.0%

VIC/TAS

TEL: (03) 8787 8288

FAX: (03) 8787 8266

www.alemlube.com.au

SA/NT

TEL: (08) 9209 3066

TEL: (08) 8241 7111

FAX: (08) 9209 3933

FAX: (08) 8241 7011

Email - [email protected]

51008P

TEL: (09) 447 1007

FAX: (09) 447 1008