Bosch Series 4 Buku Petunjuk - Halaman 15

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Oven Bosch Series 4. Bosch Series 4 50 halaman. Free standing cooker
Juga untuk Bosch Series 4: Buku Petunjuk (24 halaman), Buku Petunjuk (44 halaman), Petunjuk Instalasi dan Penggunaan Manual (16 halaman), Petunjuk Instalasi dan Penggunaan Manual (16 halaman), Buku Petunjuk (16 halaman), Buku Petunjuk (24 halaman), Buku Petunjuk (10 halaman), Buku Petunjuk (12 halaman), Buku Petunjuk (20 halaman), Buku Petunjuk (32 halaman), Panduan Petunjuk Instalasi (12 halaman), Manual (2 halaman), Panduan Referensi Cepat (2 halaman), Panduan Pengguna (16 halaman), Informasi Untuk Penggunaan (24 halaman), Buku Petunjuk (48 halaman), Informasi Untuk Penggunaan (32 halaman), Informasi Untuk Penggunaan (32 halaman), Panduan Pengguna (32 halaman), Informasi Untuk Penggunaan (32 halaman), Buku Petunjuk (24 halaman), Petunjuk Penggunaan Manual (27 halaman), Panduan Pengguna dan Petunjuk Instalasi (40 halaman), Informasi Untuk Penggunaan (32 halaman), Buku Petunjuk (36 halaman), Panduan Pengguna (24 halaman), Petunjuk Penggunaan Manual (47 halaman), Panduan Pengguna dan Petunjuk Instalasi (28 halaman)

Halaman Cetak
Bosch Series 4 Buku Petunjuk

Setting amount of rinse aid

You can set the amount of rinse aid that
should be added to a value between
§:‹‹ and §:‹‡. Setting the amount of
rinse aid to be dispensed to §:‹† will
give you a very good drying result. The
factory setting is §:‹†. Do not change
the amount of rinse aid unless there are
streaks or water stains on the utensils.
Set a lower level to avoid streaks. Set a
higher level to avoid water stains.
Here's how to set the amount of rinse
aid:
Switch on ON/OFF switch (.
1.
Hold down the programme button
2.
# and then repeatedly press the
START button P until •:‹...
appears in the display window.
Release both buttons.
3.
The LED of the # button flashes
and the digital display )" shows
the factory setting •:‹....
Press the programme button #
4.
repeatedly until the factory setting
value §:‹† appears in the display
window )".
Press the programme button 3.
5.
Each time the button is pressed, the
set value increases by one level;
when it reaches the value §:‹‡ the
display jumps back to §:‹‹ (Off).
Press START button P.
6.
The set value is saved.
Using detergent with a rinse

aid component

I n general, you can use detergent with
D e t e r g e n t w i t h a r i n s e a i d c o m p o n e n t
a rinse aid component up to a water
hardness level of 21 °dH (37 °fH, 26
°Clark, 3.7 mmol/L) without adding
rinse aid. Above a water hardness value
of 21 °dH, use additional rinse aid.
Switching off rinse aid refill
indicator
If the rinse aid refill indicator h
bothers you (e.g. if you are using a
combination detergent with a rinse aid
component), you can switch off the
rinse aid refill indicator.
Proceed as described under "Setting
rinse aid quantity" and set the level to
§:‹‹. The rinse aid refill indicator h is
switched off.
Rinse aid en
15