Anchor MegaVox Pro Panduan Pemilik - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Pembicara Anchor MegaVox Pro. Anchor MegaVox Pro 4 halaman. Public address system
Juga untuk Anchor MegaVox Pro: Panduan Pemilik (9 halaman), Panduan Pemilik (7 halaman), Panduan Pemilik (10 halaman)

Halaman Cetak

DIVERSITY WIRELESS BY ANCHOR AUDIO

Anchor Audio UHF wireless is a 16 channel, diversity wireless system that receives signals with two independent antennae.

With diversity wireless the receiver processes the stronger signal, effectively minimizing dropouts and interference from other

transmitting sources. The antennae are mounted internally so there are no obstructions or risk of damage.

CHANNEL SELECTION - BUILT-IN RECEIVER

Select a channel, set the built-in receiver & microphone transmitter

to that channel before using your wireless system.

1. Choose any available wireless

channel/frequency from 1 thru 16

(see page 7 for transmitter instructions)

2. Set the Wireless Channel Selector Knob to

the channel/frequency you choose in step 1

If you have two wireless receivers repeat above for the second

receiver. Remember each receiver/transmitter pair must be set to

different channels to avoid interference.

NOTE: Ongoing wireless interference? The frequency you selected may be in use by

other systems in the area! Change channels until you find a clear frequency!

NEED MORE HELP? View demonstration videos on proper system setup and

operation at our website - http://www.anchoraudio.com/mgx.php

MEGAVOX PRO ACCESSORIES

MEGA-6001- MegaVox PRO Companion Speaker

Unpowered companion speaker (speaker cable not included)

SC-50 - Heavy Duty Speaker Cable

50' speaker cable, connect MEGA-6001 companion speaker

SS-550 - Heavy Duty Speaker Stand

Adjustable stand made of black, anodized aluminum

NL-MEGA - Storage Cover

Durable nylon fitted speaker storage/dust cover

HC-1650M/V - Hard Case

For travel or storage - holds one Explorer PRO & accessories

SOFT-TOTE - Soft Rolling Case

Soft case w/ wheels & handle for Explorer, stand & accessories

MIC-90 - Handheld Wired Microphone

Anchor's dynamic, balanced, low impedance microphone w/

unidirectional pick-up pattern, mic "on/off" switch & 20' cable

CHANNEL

SELECTION

DIAL

RX INDICATOR

LIGHTS

ANCHOR UHF WIRELESS

WH-6000 - Handheld Microphone/Transmitter

WB-6000 - Body Pack Transmitter

Works w/ hands free microphones (mic not included)

Body Pack Transmitter Hands Free Microphones:

CM-60 - Collar Microphone

Lightweight, low-profile mic

EM-60T - UltraLite Microphone

Hands free "Over-the-Ear" mic

LM-60 - Lapel Microphone

Lightweight, clip-on lapel mic

HBM-60 - Headband Microphone

Ultra-lightweight headband mic

FEEDBACK

Feedback, a howling noise or shrill sound, is self-generated by the sound system. It's caused by a microphone picking up the sound

coming from the speaker and then re-amplifieing it. Once a feedback loop starts it continues until the system is adjusted.

FEEDBACK CAUSES

• Microphone too close, pointing towards

or in front of speaker

• Volume setting is too loud for room

• Sound reflecting off hard surfaces

AVOIDING & ELIMINATING FEEDBACK

• Point microphone in a different direction

• Keep microphone away from the speaker

• Place speaker in FRONT of the microphone

• Reduce the sound system volume levels

CONNECTING TWO OR MORE MEGAVOX PRO SOUND SYSTEMS

UNPOWERED MEGAVOX PRO COMPANION SPEAKER (MEGA-6001)

Connect one end of a speaker cable (SC-50) to the SPKR OUT jack on the back of a powered MegaVox PRO sound system.

The other end connects to the jack labeled IN on the back of a MegaVox PRO unpowered companion speaker.

NOTE: AC power is not required for an unpowered companion speaker.

POWERED MEGAVOX PRO SOUND SYSTEMS W/ LINE OUT

Connect speaker cable (EX-50PP) from LINE OUT on first powered MegaVox PRO to LINE IN on second powered MegaVox PRO.

Set volume level of the second system to maximum, this gives full volume control to the first or primary sound system.

DAISY-CHAINING

Use the Line Out method above to connect up to six powered

MegaVox PRO PA Systems. Make all connections with power off.

Set volume level to maximum on all secondary systems so the

primary unit Level Control sets the volume for the entire chain.

To avoid speaker popping, which can cause damage, power

speakers on in order, primary unit first, and power speakers off

in reverse order, primary unit last.

SPEAKER STAND SETUP

1. Loosen the Lower Collar Knob

2. Separate the stand legs until

LOWER

the leg support Cross Braces

COLLAR

are parallel to the floor

KNOB

3. Tighten the Lower Collar Knob

CROSS BRACES

CORRECT SYSTEM PLACEMENT

WRONG SYSTEM PLACEMENT

CAUTION: Feedback can damage your equipment

& may be hazardous to hearing.

EX-50PP CABLE

FIRST POWERED

MEGAVOX PRO

SECOND POWERED

MEGAVOX PRO

4. Loosen the Upper Collar Knob and

UPPER

COLLAR

extend the center pole

KNOB

5. Adjust height and retighten the

Upper Collar Knob

6. Place your Anchor sound system

on the stand