Bosch 1618EVS Panduan Petunjuk Pengoperasian/Keselamatan - Halaman 5
Jelajahi secara online atau unduh pdf Panduan Petunjuk Pengoperasian/Keselamatan untuk Alat Listrik Bosch 1618EVS. Bosch 1618EVS 24 halaman.
Halaman Cetak
BM 2610018532 01-12:BM 2610018532 01-12.qxp 1/23/12 9:21 AM Page 5
Read and understand the tool manual and
these instructions for the use of this table
with your router. Failure to follow all
instructions listed below may result in serious
personal injury.
Unplug tool before setting up in table,
making adjustments or changing bits.
Accidental start-up of the tool can cause
injury.
Fully assemble and tighten all the
fasteners required for this table and
mounting the router. Also remember to
occasionally check the stand and make sure
it is still tight. A loose stand is unstable and
may shift in use and cause serious injury.
Before operating make sure the entire
unit is placed on a solid, flat, level
surface. Serious injury could occur if tool is
unstable and tips.
Never stand on the table or use as ladder
or scaffolding. Serious injury could occur if
the table is tipped or the cutting tool is
accidentally contacted.
materials on or near the table such that it is
necessary to stand on the table or its stand
to reach them.
Never use dull or damaged bits. Sharp
bits must be handled with care. Damaged
bits can snap during use. Dull bits require
more force to push the workpiece, possibly
causing the bit to break.
Match the appropriate bit and its speed to
your application. Do not use bits that
have a cutting diameter that exceeds the
capacity of the tool. Overloading the tool
can lead to personal injury or tool failure.
Never start the tool when the bit is
engaged in the material. The bit cutting
edge may grab the material causing loss of
control of the workpiece.
Router bits are intended for wood, wood
products and plastic only. Be sure the
workpiece does not contain nails, etc.
before routing. Cutting a nail or the like will
cause the carbides to be dislodged, fly
toward the operator side, and possibly strike
you or bystanders.
Feed the workpiece against the rotation of
the bit. The bit rotates counter-clockwise
Safety Rules for Router Table
Do not store
-5-
as viewed from the top of table. Feeding
the work in the wrong direction will cause the
workpiece to "climb" up on the bit and may
lead to loss of control during operation.
Never place hands near the spinning bit.
Use push sticks, vertical and horizontally
mounted feather boards (spring sticks)
and other jigs to hold down the workpiece
and keep your hands away from the
spinning bit. Router cuts are blind cuts but
the bit still protrudes through the table and
you must be aware of the position of your
hands relative to the spinning bit.
We do not recommend cutting material
that is warped, wobbly or otherwise
unstable. If this situation is unavoidable
always cut the material with the concave
side against the table. Cutting the material
with the concave side up or away from table
may cause the warped or wobbly material to
roll; causing you to lose control, kickback and
serious personal injury may result.
Use the adjustable fence in straight
cutting applications. When routing along
an entire edge of the work, the fence, fence
faces, and adjustable outfeed fence support
shims will help maintain stability.
When the table is used without the fence,
piloted bits (or "bearing bits") must be
used. Piloted bits are used when routing
internal and external contours on a
workpiece. The bearing of the piloted bit
assists in maintaining control of the
workpiece. Whenever possible, the starter
pin should also be used.
After changing the bits or making any
adjustments, make sure the collet nut and
any other adjustment devices are
securely tightened. Loose adjustment
device can unexpectedly shift, causing loss
of control, loose rotating components will be
violently thrown.
Never touch the bit during or immediately
after the use. Contact with a spinning bit
will cause injury and after use the bit is too
hot to be touched by bare hands.
Use only Bosch replacement parts. Any
others may create a hazard.