Bosch 2 Panduan Pengguna dan Petunjuk Instalasi - Halaman 12

Jelajahi secara online atau unduh pdf Panduan Pengguna dan Petunjuk Instalasi untuk Alat Listrik Bosch 2. Bosch 2 16 halaman. Mini blender
Juga untuk Bosch 2: Panduan Instalasi Cepat (16 halaman), Panduan untuk Instalasi dan Penggunaan (18 halaman), Manual Petunjuk Asli (13 halaman), Manual Petunjuk Asli (22 halaman), Buku Petunjuk (32 halaman), Panduan Pengguna (28 halaman), Buku Petunjuk (42 halaman), Panduan Petunjuk Pengoperasian (8 halaman), Buku Petunjuk (8 halaman), Buku Petunjuk (12 halaman), Panduan Memulai Cepat (2 halaman), Panduan Memulai Cepat (9 halaman), Buku Petunjuk dan Petunjuk Instalasi (36 halaman), Panduan Pengguna dan Petunjuk Instalasi (48 halaman), Panduan Petunjuk Pengoperasian (26 halaman), Panduan Referensi Cepat (2 halaman), Panduan Pengguna dan Petunjuk Instalasi (24 halaman), Buku Petunjuk (42 halaman), Informasi Untuk Penggunaan (28 halaman), Panduan Pengguna (40 halaman), Panduan Pengguna dan Petunjuk Instalasi (35 halaman), Panduan Pengguna (24 halaman)

Halaman Cetak
Bosch 2 Panduan Pengguna dan Petunjuk Instalasi
en Installation instructions
The bottom edge of the appliance is identical to the
lower edge of the drilling template.
5.
Ensure that there are no electrical wires, gas pipes
or water pipes in the area where holes are to be
drilled.
6.
Drill holes with a diameter of 8 mm.
7.
Drill the hole depth in accordance with the length of
the screws.
8.
Insert the wall plugs flush with the wall.
9.
Remove the angle bracket for the flue duct.
10.
Screw in two fastening screws with washers to ap-
prox. 5 mm.
11.
Attach and align the appliance.
12.
Mark the hole for the safety screw.
13.
Remove the appliance once more.
Attaching the appliance
1.
Drill an 8 mm hole for the safety screw.
2.
Insert the wall plugs flush with the wall.
3.
Attach the appliance.
4.
Screw in the safety screw with the washer.
You can also use the right or left hole opening.
Fitting the flue duct
1.
To separate the flue duct sections, remove the ad-
hesive tape.
12
2.
Remove the protective foil from both flue duct sec-
tions.
3.
Note:
¡ To prevent scratches, lay paper over the edges
of the outer flue duct section to protect the sur-
face.
¡ The slots on the inner flue duct section should
point downwards.
Push one flue duct section into the other.
4.
Insert the lower flue duct section into the brackets
on the left and right on the appliance.
5.
Screw the upper flue duct to the sides of the fixing
bracket using 2 short screws.
6.
Fit the grease filters.
To avoid causing damage, do not bend the grease
filters.
Fitting the filter cover
WARNING ‒ Risk of injury!
Components inside the appliance may have sharp
edges.
▶
Wear protective gloves.
Risk of injury from glass splinters.
▶
Protect the filter cover against impact.
▶
Do not drop the filter cover.
▶
Wear protective goggles during installation.
1.
Align the filter cover at an angle of 90° to the appli-
ance.