Anchor AnchorMAN Panduan Pemilik - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Sistem interkom Anchor AnchorMAN. Anchor AnchorMAN 4 halaman. Wireless intercom system
Juga untuk Anchor AnchorMAN: Panduan Pemilik (6 halaman)

Halaman Cetak

rEChargEablE baTTEriES

AnchorMAN belt packs include 4 "AA" NiMH rechargeable batteries and AC Gang Charger. Fully charged NiMH batteries yield

approximately 7 hours of normal use. Alkaline "AA" batteries can be used but battery life will decrease by half. Connecting the

AC charger to a belt pack with alkaline batteries installed could seriously damage the system.

iNSTall baTTEriES

Slide battery compartment door to remove

Install 4 "AA" NiMH rechargeable batteries

NOTE: Place "–" end of battery against spring.

Replace battery compartment door

NOTE: Flashing group lEd indicates battery low.

CauTiON: do not attempt to charge alkaline batteries.

Some users are required (for emergency preparedness, etc.) to leave their AnchorMAN units plugged into the charger at all times.

For these applications we recommend replacing the rechargeable batteries every 12 months.

FrEquENTly aSkEd quESTiONS

CaN i uSE my OWN hEadSET?

The AnchorMAN is designed to work with dynamic microphone elements. (Shields can be connected to chassis ground pin.)

Headset pin configuration: 1 = Mic (–), 2 = Mic (+), 3 = Headphone (–), 4= Headphone (+)

i'vE ruN OuT OF baTTEry liFE, NOW WhaT?

You can substitute "AA" alkaline batteries for the rechargeable batteries. However, connecting the battery charger to the belt

pack when alkaline batteries are installed could seriously damage your belt pack.

CaN my aNChOrmaN WOrk WiTh OThEr WirElESS iNTErCOm SySTEmS?

No. AnchorMAN uses a proprietary design and software exclusive to the product.

CaN SOmEONE EavESdrOP ON my CONvErSaTiON?

No. AnchorMAN is not penetrated by common scanners.

iF i brEak a hEadSET, WhaT dO i dO?

The H-2000 and H-2000S headsets are covered by a two-year warranty. Follow the instructions in the Getting Started section

on page 2 for a Return Authorization. AnchorMAN headsets are sold separately if a replacement is needed.

CaN i add bElT PaCkS TO my NETWOrk?

Yes. It's designed to accommodate an unlimited number of listeners. However, the maximum number of people that can

speak at once in one group is limited to four. Belt packs that are set to the same USER ID (DIP 1 and 2) and GROUP will in-

terfere if they transmit at the same time. However, if two users are not expected to speak at the same time, they can share a

USER ID.

ChargE baTTEriES

Connect Gang Charger (included) into Charging Port on bottom of

belt packs

Plug Gang Charger into AC outlet

(Charging Port LED on = battery charging)

Charge belt pack for 5 hours

(Charging Port LED off = battery fully charged)

bP-900 bElT PaCk

The ergonomically designed BP-900 AnchorMAN belt pack features an XLR headset jack, heavy duty antenna, headset volume

control, microphone sensitivity control, group selection, PTT (push to talk) and transmission indicator LED. The belt pack is pow-

ered by 4 (included) "AA" NiMH rechargeable batteries.

grOuP SElECTOr

To create a belt pack group, each member must set their

Group Selector to the same letter – A, B, C or D. Press the

GRP Button to change groups. The LED will light indicating

the selected Group (A, B, C, D) .

Example: Film Crew

The director assigns photography to Group A, sound to

Group B and lighting to Group C. He can then be a part

of any group by simply pressing the Group Selector But-

ton to the desired group.

Due to the unique environmental conditions found at some locations (Example: Next to a radio station transmission tower.) you

may find that one of the four Group settings experiences disruptive interference. Simply discontinue use of the effected Group

and try the three remaining Groups to identify the clearest signal. For best results try the Group farthest from the affected Group

first (If Group A has interference try Group D) .

Due to the use of other wireless devices in your area, it may be possible for one or more channels within a frequency group to

experience RF (radio frequency) interference. It may be necessary to audition all frequency groups prior to selecting the one

that performs best for your application.

PuSh TO Talk mOdE / aCTivE mOdE

Push to Talk Mode (PTT) – Default mode when the PWR button is pushed. Press

PTT button to speak to Group, release PTT button to listen.

Active Mode – Hands free voice activated operation (VOX) requires adjusting the

Microphone Sensitivity level. Upon power up, belt packs default to low requiring

PTT operation. Push the "+" button repeatedly to increase mic sensitivity until

transmission is activated by the sound of your voice.

For videos on how to setup & use the anchormaN:

www.anchoraudio.com

TraNSmiT/rECEivE iNdiCaTOr lEd

grOuP SElECTOr lEd

grOuP

SElECTOr

buTTON

PuSh TO Talk buTTON

POWEr buTTON

miCrOPhONE SENSiTiviTy