Forme HTR7006206OP Panduan Petunjuk Instalasi - Halaman 3
Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Penghangat Makanan Forme HTR7006206OP. Forme HTR7006206OP 9 halaman. Multi bar towel warmer
Halaman Cetak
TOWEL WARMER INSTALLATION INSTRUCTIONS
CODE REQUIREMENTS
•
Please note that this appliance must be installed as prescribed by the relevant wiring rules and regulations, including the
regulations covering installation of appliances and accessories in 'wet areas' such as bathrooms, showers and laundries.
Installations should be in accordance with National and Local Electrical Codes applicable in both the US and CANADA.
•
In plain words, make sure that all wiring connections are done safely and according to code. Check with a professional
approved electrical box. Again, follow the instructions and hire licensed help where required to comply with your local
regulations.
•
This appliance requires a connection to ground
•
The heated towel warmer should be mounted vertically with the cord exiting from the base; it should be positioned
DO'S, DONT'S AND SAFETY INFORMATION
As with any electrical appliance, you should be aware of basic safety precautions when using this heated towel warmer.
•
Because this appliance gets hot, young children and impaired people or persons with disabilities should be supervised
when nearby. Do not let children treat the towel rail as a toy.
•
Do not hang excessive loads from the towel warmer rails. While securely anchored to the wall when properly installed,
it is not intended to replace or serve as a grab bar.
•
The towel warmer should NOT be used for anything other than its intended use of warming up and drying bathroom
towels.
•
Occasionally wipe down your towel warmer from time to time with a damp cloth and/or a stainless steel cleaner.
Do not use any abrasives or corrosive cleaners.
•
Be aware that the towel rail will get slightly hotter than normal during warmer weather and when insulated by towels.
•
Do not put the towels, or anything else which has been in contact with hazardous liquids, on this towel rail.
•
Do not immerse the towel rail in any liquid.
ELECTRICAL
•
•
Electrical work should be performed by a licensed electrician.
•
Make sure the supply cord never touches heated surfaces. If the electrical cord or connection is damaged DO NOT
attempt to repair; please contact the supplier.
•
Do not install towel rails in areas which may be subjected to saturation of water resulting in ingress of moisture.
It is recommended that all units are protected via a GFCI circuit. The GFCI can be included on your breaker at the panel, or
built into the thermostat.
4
TOWEL WARMER INSTALLATION INSTRUCTIONS
MOUNTING YOUR TOWEL WARMER
Do note that all models will have the power cord exiting on the bottom right bracket (when facing the towel
warmer mounted on the wall). Plan accordingly when setting up switches and electrical rough-in.
POSITIONING YOUR TOWEL WARMER
Align left side to studs
Select a desired position to mount the towel rail i.e. at least 600mm/2 feet above the floor and 300mm/1 foot
away from all permanent fixtures in the surrounding area (toilet, vanity, etc).
The left side of your towel warmer must be anchored into a stud. Use a stud-finder tool to locate the 2x4 behind
your drywall and mark it with a pencil. Hold your towel warmer level at the desired height and line it up with the
stud on the left hand side.
Using a pencil, draw around the end of each tube to mark their positions on the wall. Make sure your marks are
level and square as these will determine where you will secure the device to the wall.
Screw the mounting inserts securely to the wall at the locations marked. Press the towel warmer onto the
mounting inserts gradually, checking that each leg is lined up with the mounting inserts before applying force.
Mount the towel warmer with a single grub screw on each of the 4 brackets.
Power cord entry
Apply junction box if
required by code.
5