Common Sense RC CELLSPY8 Panduan Pengguna dan Manual

Jelajahi secara online atau unduh pdf Panduan Pengguna dan Manual untuk Alat Ukur Common Sense RC CELLSPY8. Common Sense RC CELLSPY8 2 halaman. Voltage checker

Halaman Cetak

Common Sense RC Cell Spy 8 User Guide and Manual - #CELLSPY8

1. INTRODUCTION

The Common Sense RC Cell Spy 8 is a clever device that can show you the condition of your battery packs while also serving as a battery

balancer and servo tester.

It can be used with the most common battery types used for RC modeling:

• Li-Ion (Lithium Ion)

• NiCd (Nickel Cadmium)

For Lithium battery types (Li-Po, Li-Ion, Li-Fe, Li-HV), the Cell Spy 8 can support 2S~8S without the need for an additional power supply. To test

1S Lithium batteries, you need to also connect more than 3S of Nickel batteries or a 5V UBEC to the NiCd/MH port to provide enough voltage

for the Cell Spy 8 to power on, then press the TYPE/SETUP MENU button to select the correct battery type.

For Nickel battery types (NiCd or NiMH), the Cell Spy 8 can support 4S~8S without the need for an additional power supply. If you need to

test less than 4S of Nickel batteries, you need to connect a 2~8S Lithium battery to the 9-pin/Lithium port to provide enough voltage for

the Cell Spy 8 to power on.

2. CONNECTING a baTTERY PaCk

There are two battery connection ports:

Lithium battery: The 9-pin/Lithium battery port has 9 pins with standard 2.54mm spacing. The balance plug of your Lithium battery should

be plugged into this port with the outside negative (black) wire aligned with the

Nickel battery: The Nickel battery port is labeled Servo 5V Power IN NiCd/MH. It has 3 pins with 2.54mm spacing, designed for receiver/servo

type plugs. The main leads of the Nickel battery receiver pack generally has 2 wires. The connector should be plugged into this port with

the negative (black) wire aligned with the

3. PaRaMETER SETTINGS

The Cell Spy 8 allows you to adjust certain parameters for battery and servo testing, including discharge end voltage, servo signal range, and

more. To enter Parameter Setting Menu, connect a battery to the Cell Spy 8, then press and hold the TYPE/SETUP MENU button for 1 second.

Press the CELL/SERVO TEST button to reduce the parameter, or press the MODE/DISCHARGE button to increase the parameter. Press the

TYPE/SETUP MENU button again to advance to the next parameter setting. Press the TYPE/SETUP MENU button again to advance to the

next parameter setting.

Voltage

Display

(Default Mode)

Voltage Display Mode

Servo Test Signal Range Setting:

500~2500us,1000~2000us

Battery Voltage Capacity Checker / Balance Discharger / Servo Tester

• Li-Po (Lithium Polymer)

• NiMH (Nickel Metal Hydride)

symbol on the Cell Spy 8.

Hold

Press

Discharge

Cut-oﬀ Voltage

TYPE

Setting

TYPE

Hold

Voltage

TYPE

Display

Servo Test Signal

Range Setting

Lithium battery and Nickel battery

Connection Diagram

(Can simultaneously connect Lithium

battery and Nickel battery)

Press

Servo Test

Frequency

Signal Range

Setting

TYPE

Setting

Hold

Voltage

Hold

Voltage

TYPE

Display

TYPE

Display

Discharge Cut-off

Voltage Setting

Discharge Cut-off Voltage Setting

Range: 2.000~4.200V

LCD backlight Opening

Time Setting

LCD Backlight Opening Time

Setting: Off, 10s~60s, On

• Li-Fe (Lithium Ferrite)

• Li-HV (High Voltage Lithium Polymer)

symbol on the Cell Spy 8.

Press

LCD Backlight

Opening Time

TYPE

Setting

TYPE

Hold

Voltage

TYPE

Display

Servo Test Frequency Setting

Servo Test Frequency Setting:

50Hz, 60Hz, 100Hz, 125Hz,

200Hz, 250Hz, 300Hz

Sound Switch Setting

Sound Switch Setting: On, Off

Sound Switch

Setting

Press TYPE

Button