Dreame VPV11A Panduan Pengguna - Halaman 8

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Penyedot Debu Dreame VPV11A. Dreame VPV11A 10 halaman. Cordless stick vacuum

Halaman Cetak

Accessories

Note: The illustrations in this manual are

indicative only. The actual product may

differ.

1. Extension Rod

2. Combination Tool

3. Charger

4. Multi-Surface Brush

5. Wall Mount (Including screw × 2, wall

plug × 2)

6. Motorized Mini-Brush

Fig. A

Components

1. Power Button (Press to turn on/Release

to turn off)

2. Suction Level Status Indicator

Turbo

Med

Eco

3. Suction Level Switch

4. Dust Cup

5. Dust Cup Release Button

6. Multi-Surface Brush

7. Antistatic Contact

8. Battery Status Indicator

9. Battery Pack Release Button

10. Charging Port

11. Extension Rod Release Button

12. Extension Rod

13. Brush Release Button

Fig. B

Installation

• Vacuum and Accessories Installation

Fig. C-1

• Wall Mount Installation

The mount should be installed in a cool,

dry place near a power outlet. Make sure

the installation area is clear of any pipes

such as gas or water lines, and air ducts,

electric wires and cables, or drainage

lines.

1. Before installation, measure the wall

in the height of 102 cm (40.2 inches)

above the ground.

2. Mark and drill two 8 mm (0.315 inch)

diameter holes into the wall with an

electric drill.Insert the wall plugs into

the holes.

3. Align the position holes on the mount

with the holes on the wall. Fasten it to

the wall with the included screws.

Fig. C-2

Operation

Charging

• Connecting the charger to the wall

mount

1. Rotate the clip in the bottom of wall

mount 90 degrees counterclockwise to

remove it from the mount.

2. Insert the power cord into the notch on

the clip.

3. Rotate the clip 90 degrees clockwise

until it clicks into place.

Fig. D-1

• Put the vacuum cleaner on the wall

mount and plug the charger into the

charging port.

Fig. D-2

• Battery Status Indicator

Fig. D-3

Charging

Fully charged

Charging

Discharging

Battery Level ≥ 10%

Battery Level < 10%

Solid white

Blinking white

off

Note:

1. The vacuum cannot be used while

charging.

2. Fully charge the vacuum before using

it for the first time. This will take about

4 hours.

3. Vacuuming at Turbo mode for a

prolonged period will cause the battery

to heat up, which increases charging

time. Allow the vacuum to cool down for

30 minutes before charging it.

Working Method

Press and hold the power button to start

the appliance, and release the button to

stop immediately.

Fig. D-4

Switching Suction Level

Press briefly to switch between eco, med

and turbo mode.

Fig. D-5

Using Different Accessories

• Multi-Surface Brush

- When using on baby play mats, carpets

or for vacuuming coffee beans, pop corn

and other pellets, turn on the switch on

the brush.

- When vacuuming on tiles, wooden floors

or other hard surfaces, turn off the switch.

Fig. D-6

Note:

1. The multi-surface brush can be

attached directly to the vacuum.

2. When the appliance starts, the

lights in front of the brush roller

will automatically turn on, which is

convenient for use.

• Combination Tool

Suitable for vacuuming cracks, corners

of doors and windows, stairs, and other

hard-to-reach places.

Fig. D-7

• Motorized Mini-Brush

For vacuuming dirt, pet hair, and other

stubborn debris from sofas, bedding,

and other fabric surfaces.

Note: It is not recommended to vacuum

on fragile surfaces, such as silk.

Fig. D-8

Note:

1. If any rotating part becomes stuck, the

vacuum may shut off automatically.

Remove any trapped foreign objects,

then resume use.

2. When the battery becomes overheated,

the vacuum will automatically shut

off. Wait until the battery temperature

returns to normal, then resume use.

Care &

Maintenance

Tips:

1. Always use genuine parts to keep your

warranty from being void.

2. If the filter or nozzle becomes clogged,

the vacuum will stop working shortly

after being turned on. Clean it to restore

functionality.

3. If the vacuum is not used for an

extended period, fully charge it,

unplug its charger, remove the battery,

and store it in a cool, low-humidity

environment away from direct sunlight.

To avoid over-discharging the battery,

recharge the battery at least once every

three months.

Cleaning the Vacuum

Wipe the vacuum with a soft dry cloth.

Cleaning the Dust Cup,

Pre-Filter, and Cyclone

Assembly

Before cleaning the dust cup, disconnect

the charger and keep the vacuum's power

button in the off position.

• Press the dust cup release button and

remove it from the vacuum.

Fig. E-1

• Remove the pre-filter first, and then

rotate the cyclone system to lift it out.

Fig. E-2

• Empty the dust cup.

Fig. E-3

• Rinse the cyclone assembly, pre-filter,

and dust cup until they are clean. After

washing, air dry for at least 24 hours.

Fig. E-4

Note:

1. It is recommended to clean the dust

cup after use.

2. It is recommended to clean the

cyclone system and pre-filter at least

once every 3 to 4 months.