Bosch Professional GWS 24-180 JZ Manual Petunjuk Asli - Halaman 10
Jelajahi secara online atau unduh pdf Manual Petunjuk Asli untuk Alat Listrik Bosch Professional GWS 24-180 JZ. Bosch Professional GWS 24-180 JZ 24 halaman.
Halaman Cetak
10 | English
Angle grinder
GWS 24-180 GWS 24-230 GWS 24-180
Overload protec-
tion
Weight according to EPTA-Procedure 01:2014
– with low-vibra-
kg
tion auxiliary
handle
– with standard
kg
auxiliary
handle
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Only for power tools without starting current limitation: Switching these on causes the voltage to drop briefly. Other tools may be adversely af-
fected by these if the conditions in the electricity supply are unfavourable. Malfunctions are not to be expected for system impedances
below 0.058 ohm.
Fitting
Fitting Protective Equipment
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Note: If the grinding disc breaks during operation or the
holding fixtures on the protective guard/power tool become
damaged, the power tool must be sent to the after-sales ser-
vice immediately; see the "After-Sales Service and Applica-
tion Service" section for addresses.
Protective guard for grinding
Place the protective guard (6) on the spindle collar. Adjust
the position of the protective guard (6) to the requirements
of the operation and lock the protective guard (6) with the
locking screw (7).
Adjust the protective guard (6) such that sparking in
u
the direction of the operator is prevented.
Protective guard for cutting
Always use the protective guard for cutting (14) when
u
cutting bonded abrasives.
Provide sufficient dust extraction when cutting stone.
u
The protective guard for cutting (14) is fitted in the same
way as the protective guard for grinding (6).
Extraction guard for cutting with a guide block
The extraction guard for cutting with a guide block (22) is fit-
ted in the same way as the protective guard for grinding (6).
Side handle
Do not operate your power tool without the side
u
handle (4).
Screw the side handle (4) on the left or right of the machine
head depending on how your are working.
Low-vibration auxiliary handle
1 609 92A 5TG | (25.11.2020)
–
–
5.7
5.9
5.6
5.8
/ II
/ II
Screw the auxiliary handle
(4) on the right or left of the
GWS 24-230
GWS 24-180
P
P
–
–
5.7
5.9
5.6
5.8
/ II
/ II
machine head depending on the working method.
The low-vibration auxiliary handle reduces vibration, en-
abling the tool to be used safely and more comfortably.
Do not operate your power tool without the side
u
handle (4).
Do not make any alterations of any kind to the auxili-
u
ary handle.
Do not continue to use a damaged auxiliary handle.
Hand guard
Always fit the hand guard (16) when working with the
u
rubber sanding plate (18) or with the cup brush/disc
brush/flap disc.
Attach the hand guard (16) to the side handle (4).
Fitting the abrasive tools
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
Clean the grinding spindle (5) and all the parts to be fitted.
Lock the grinding spindle with the spindle lock button (1)
before clamping and releasing the abrasive tools.
Do not press the spindle lock button while the grind-
u
ing spindle is moving. The power tool may become dam-
aged if you do this.
Grinding/cutting disc
Pay attention to the dimensions of the abrasive tools. The
diameter of the hole must match that of the mounting flange.
Do not use an adapter or reducer.
When using diamond cutting discs, ensure that the arrow in-
dicating the direction of rotation on the diamond cutting disc
matches the direction of rotation of the power tool (see the
direction of rotation arrow on the machine head).
See the graphics page for assembly instructions.
GWS 24-230
JZ
JZ
●
●
5.8
6.0
5.7
5.9
/ II
/ II
Bosch Power Tools