Bosch Programme Table Petunjuk Pengoperasian dan Pemasangan - Halaman 20

Jelajahi secara online atau unduh pdf Petunjuk Pengoperasian dan Pemasangan untuk Pengering Bosch Programme Table. Bosch Programme Table 29 halaman. Front-loading washing machine
Juga untuk Bosch Programme Table: Buku Petunjuk (10 halaman), Panduan Petunjuk Pengoperasian (8 halaman), Buku Petunjuk (8 halaman), Buku Petunjuk (8 halaman), Buku Petunjuk (8 halaman), Panduan Petunjuk Pemasangan dan Pengoperasian (32 halaman), Panduan Petunjuk Pemasangan dan Pengoperasian (32 halaman), Buku Petunjuk (10 halaman), Buku Petunjuk (10 halaman), Buku Petunjuk (8 halaman), Buku Petunjuk (10 halaman), Buku Petunjuk (8 halaman), Petunjuk Instalasi dan Penggunaan Manual (8 halaman), Buku Petunjuk (8 halaman), Buku Petunjuk (8 halaman), Panduan Petunjuk Pengoperasian (10 halaman), Panduan Petunjuk Pengoperasian (10 halaman), Panduan Petunjuk Pengoperasian, Perawatan, dan Pemasangan (24 halaman), Panduan Petunjuk Pengoperasian (8 halaman), Petunjuk Penggunaan Manual (10 halaman), Buku Petunjuk (10 halaman), Panduan Petunjuk Pengoperasian (8 halaman), Buku Petunjuk (8 halaman), Buku Petunjuk (10 halaman), Buku Petunjuk (8 halaman), Buku Petunjuk (8 halaman), Buku Petunjuk (10 halaman), Buku Petunjuk (8 halaman), Buku Petunjuk (8 halaman), Panduan Petunjuk Pengoperasian, Perawatan, dan Pemasangan (24 halaman), Panduan Petunjuk Pengoperasian (8 halaman), Buku Petunjuk (10 halaman), Buku Petunjuk (10 halaman), Buku Petunjuk (8 halaman)

Halaman Cetak
Bosch Programme Table Petunjuk Pengoperasian dan Pemasangan
i
Do not damage the air cooler!
Clean with warm water only; do
not use hard/sharp edged
objects!
7. Clean the air cooler completely,
drain thoroughly.
8. Clean the seals.
9. Re insert the air cooler, handle
at the bottom!
10. Unscrew both locking levers.
11. Close the maintenance flap
until it locks into position.
20
Cleaning the moisture
sensor
Occasionally the moisture sensor
has to be cleaned because a fine
layer of transparent buildup is
deposited on the sensors.
This deposit can easily be removed
by wiping the sensors (the two bars
next to the lint filter) with a cloth and
a little white vinegar.
Use white vinegar only!
Clean the moisture sensor once
a month.
Cleaning the bearing
shield
Over time, fluff from the drying
process collects in the bearing
shield.
This fluff can be easily removed
using your vacuum cleaner, at least
once a month.
Changing the light
bulb
The dryer light turns on inside the
drum when you open the door.
To change the light bulb:
1. Turn off the circuit breaker.
2. Pull out power supply plug.
3. Open the door and locate the
light bulb on the upper center
of the seal.
4. Loosen the screw of the cover
and open the cover.
5. Turn bulb counterclockwise.
Replace the bulb with a new
appliance bulb only (obtainable
through customer service).
6. Replace the cover and secure
with the screw.
7. Plug in dryer or reconnect
power supply.