ANDI APFH75TE Panduan Instalasi dan Petunjuk Pengguna - Halaman 6

Jelajahi secara online atau unduh pdf Panduan Instalasi dan Petunjuk Pengguna untuk Kompor ANDI APFH75TE. ANDI APFH75TE 6 halaman.

Halaman Cetak

I N S T A L L A T I O N I N S T R U C T I O N S

GAS CONNECTION

The gas inlet is situated at the rear of the appliance, 250mm from

the right-hand side and 58mm from the rear of the cooktop. If

necessary, cut a suitable hole in the back of the cabinet for the

entry of the gas supply and electric cable.

IT IS RECOMMENDED THAT A SERVICE TAP AND UNION BE

FITTED ADJACENT TO THE APPLIANCE INLET TO FACILITATE

FUTURE SERVICING. ENSURE THE REGULATOR SUPPLIED

(FOR NATURAL GAS) IS FITTED BEFORE APPLIANCE.

VERY IMPORTANT FOR THE INSTALLER

Do not attempt to turn or stress the threaded elbow of the manifold:

you risk damage to this part of the gas appliance which may void

the manufacturers warranty.

BEFORE LEAVING

Check all connections forgas leaks with soap and water. DO NOT use

a naked flame for detecting leaks. Ignite all burners to ensure correct

operation of gas valves, burners and ignition. Turn gas taps to low

flame position and observe stability of the flame. When satisfied with

the hotplate, please instruct the useron the correct method of operation.

In case the appliance fails to operate correctly after all checks have

been carried out, call the number on the data label on the front of this

instruction manual.

ELECTRICAL CONNECTION

IMPORTANT

This hotplate is supplied with a plug & cord, simply plug into

a 3 pin household socket outlet which is properly earthed.

In order to avoid hazard, any electrical work performed on

this equipment or its associated wiring, should only be done

by persons authorised by the supplier or similarly qualified

persons.

The wires in the mains lead are coloured in accordance with the

following code:

GREEN & YELLOW.........................................................EARTH

BLUE ...........................................................................NEUTRAL

BROWN ..............................................................................LIVE

If the supply cord is damaged, it must be replaced by the

manufacturer or its service agent or similarly qualified person in

order to avoid a hazard.

WARNING: THIS APPLIANCE MUST BE EARTHED.

The flexible mains lead and plug must not be in contact with hot

surfaces.

Electric diagram for

multi-sparks lighter

1 Spark plug for ignition

2 Ignition

3 Switch for ignition

4 Terminal box

L N

Fig. 5

SERVICING FOR HOT PLATES

All service should be carried out be a authorised service technician

only.

WARNINGS

Before performing any repair or operation, switch the appliance

off and close the gas tap.

The manufacturer declines all responsibility for any damage to

persons, animals or things caused by failure to observe the rules

indicated above. In case it is necessary to repair or replace the

inside components, act as follows:

DISASSEMBLY OF WORK-TOP

- disconnect the electrical supply cable

- disconnect the gas supply tube

- remove the grids

- remove burners and flame-spreaders

- remove the knobs from the facia-panel

- disassemble the work-top from the cabinet unscrewing screws

blocking locking bridles.

Remove the hob from the top.

A) On the lower plate of the hob, on the outside there are some

visible screws fixing the burners and the gas manifolds to the

chassis.

Once these screws or screw-nuts are unscrewed, it is possible

HOB

to replace the components inside the hob .

S E R V I C E I N S T R U C T I O N S

B) The hob is fixed in its upper part to the burners by means of

some visible screws. If these screws and the nut blocking the

taps to the hob are screwed, it is possible to open the appliance

and to reach the inside components (see picture below).

GAS CONVERSION AND ADJUSTMENT

When used with natural gas all burners have been preset at our

factory and further adjustment should not be necessary. Conversion

kits to other gases are available from the place of purchase. Do

not attempt to fit the conversion kit yourself. Conversion to

U-LPG should only be carried out by an authorized technician.