Andis 65340 Panduan Petunjuk Penggunaan dan Perawatan - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Petunjuk Penggunaan dan Perawatan untuk Gunting Rambut Andis 65340. Andis 65340 13 halaman. Andis 65340 use and care instructions

Halaman Cetak

NoTe: The battery pack is designed to run the clipper for

about one hour. A clean, sharp, well-oiled blade will provide

the best run time.

3. Before initial use, battery pack must be charged for

a minimum of ten hours.

4. The charger base has a blue indicator light. The indicator

light will remain "ON" when the battery is charging.

5. You can keep the clipper in the charger when not in use.

The charger will maintain the battery at full charge and the

blue light will stay on. The unit has a Nickel Metal Hydride

battery that cannot be damaged by overcharging. However,

we recommend that the charger be unplugged if the clipper

won't be used for seven or more days.

sAFeTY RULes FoR CHARGeR AND BATTeRY PACK

1. Clipper motor switch must be in the "OFF" position for the

charger to operate properly. Do not return the clipper to the

charger base with the motor switch in the "oN" position.

If the clipper is accidentally put on the charger base in the

"ON" position, remove it promptly. Turn clipper off and return

to the charger base.

2. Do not insert anything metallic into the battery pocket

of the charger base (Diagram C).

3. Do not attempt to charge any other battery other than

the battery pack designed for your Andis AGR+ Clipper.

4. Do not store battery or charger where it is under 50°F

or over 104°F, as damage may occur (Diagram D).

5. Do not expose the charger base or the battery pack

to excessively damp conditions (Diagram E).

6. Avoid dropping the charger base and the battery pack.

Do not attempt to use a damaged battery pack or charger.

7. Clean external parts of charger with a soft brush or damp rag.

Do not use harsh abrasives, detergents, or solvents (Diagram F).

GUIDeLINes FoR BATTeRY PACK AND CHARGeR Use

Diagram B

1. Your clipper, battery pack, and charger function as several interacting electrical systems. Good

electrical contact must be maintained in order for the motor to deliver full power and the battery

to charge properly. Limited or erratic performance caused by dirt or age can be restored in the

majority of the cases if you do the following:

A. Problem: Clipper motor starts and stops as if there was a loose electrical connection.

solution: Remove the battery pack from the clipper. Examine the battery pack opening in the

clipper. Locate the two sets of motor contacts. Gently squeeze the metal leaves until they are

about 1/16 apart using a long pliers or similar. Do NoT squeeze the metal leaves completely

together or the battery pack will not re-insert.

B. Problem: Charger does not fully charge the battery. solution: Clean the battery pack bottom

contacts (the portion inserted into the charging pocket). Clean the charger contacts. Re-align

the charger contacts. To clean the battery pack contacts, rub gently with a pencil eraser until

they are brightly polished. Use a cotton swab and 91% isopropyl alcohol to remove any residue

or dirt. Denatured alcohol can also be used. Use care, as both products are flammable. Clean

the charger contacts in the same way UNPLUG CHARGeR FIRsT. Make sure eraser dust and

cleaners do not get inside the charger base. To re-align the charger contacts, again make sure

it is unplugged, and gently pull the metal loops on the four contacts forward sLIGHTLY.

Do not severely bend, deform, or damage the contacts.

C. Problem: Charger lights flash on and off as clipper or battery is moved side to

side in the charger pocket. solution: Re-align the charger contacts as noted above.

2. To increase the life of your battery pack, do not run the clipper until the motor completely stops.

Diagram C

When the motor noticeably slows during clipping where it did not before, charge the battery pack.

3. A new battery pack may not charge to full capacity on the first use. This is normal and does not

indicate a problem with the battery pack or charger. About five cycles of using the clipper until

the motor slows, and then recharging it will bring the battery pack to full capacity. This is called

"forming" a battery pack.

4. It is normal for the charger to become warm to the touch during operation.

5. Disconnect the charger from the AC outlet if long periods of non-use are anticipated.

6. Never store batteries in a discharged condition. Recharge them immediately after they are discharged.

Diagram D

7. Many factors influence the life of the battery pack. A battery pack that has received heavy use

and is over a year old, may not give the same run-time performance as a new battery pack.

Car Adapter for Model AGR+ Charging stand (included)

• By using the included car adapter, you can operate your Model

AGR+ charging stand within a motor vehicle that is equipped

Diagram E

with a 12V power outlet (lighter adapter).

CAR ADAPTeR oPeRATING INsTRUCTIoNs

1. Remove power cord from back of charging stand.

2. Plug car adapter cable into back of charging stand. (Diagram G)

3. Insert the car adapter into the 12V power outlet (cigarette lighter

adapter) in your car. The green light on the car adapter will turn

Diagram F

on to indicate that the adapter is plugged in.

Plugs into charging stand

Indicator light

Plugs into 12V

power outlet