Bosch 4 V-LI Manual Petunjuk Asli - Halaman 7

Jelajahi secara online atau unduh pdf Manual Petunjuk Asli untuk Bor Bosch 4 V-LI. Bosch 4 V-LI 10 halaman. Professional
Juga untuk Bosch 4 V-LI: Petunjuk Manual (31 halaman), Manual Petunjuk Asli (7 halaman), Manual Petunjuk Asli (7 halaman), Manual Petunjuk Asli (48 halaman), Manual Petunjuk Asli (14 halaman), Manual Petunjuk Asli (15 halaman)

Halaman Cetak

OBJ_BUCH-832-004.book Page 15 Wednesday, December 12, 2012 10:31 AM

Cordless Impact Screwdriver

Article number

Rated voltage

No-load speed

Impact rate

Maximum torque, hard screwdriving

application according to ISO 5393

– ¼" hexagon socket

–  ½"

Bolt size

Tool holder

Weight according to EPTA-Procedure

01/2003

* Value dependent of the battery pack being used

Noise/Vibration Information

Measured sound values determined according to EN 60745.

Typically the A-weighted noise levels of the product are:

Sound pressure level 96 dB(A); Sound power level

107 dB(A). Uncertainty K =3 dB.

Wear hearing protection!

Vibration total values a

(triax vector sum) and uncertainty K

determined according to EN 60745:

Impact tightening of fasteners of the maximum capacity of the

tool: a

=12 m/s

, K=1.5 m/s

The vibration emission level given in this information sheet

has been measured in accordance with a standardised test

given in EN 60745 and may be used to compare one tool with

another. It may be used for a preliminary assessment of expo-

sure.

The declared vibration emission level represents the main ap-

plications of the tool. However if the tool is used for different

applications, with different accessories or poorly maintained,

the vibration emission may differ. This may significantly in-

crease the exposure level over the total working period.

An estimation of the level of exposure to vibration should also

take into account the times when the tool is switched off or

when it is running but not actually doing the job. This may sig-

nificantly reduce the exposure level over the total working pe-

riod.

Identify additional safety measures to protect the operator

from the effects of vibration such as: maintain the tool and the

accessories, keep hands warm, organise work patterns.

Declaration of Conformity

We declare under our sole responsibility that the product de-

scribed under "Technical Data" is in conformity with the fol-

lowing standards or standardization documents: EN 60745

according to the provisions of the directives 2011/65/EU,

2004/108/EC, 2006/42/EC.

Technical file (2006/42/EC) at:

Robert Bosch GmbH, PT/ETM9,

D-70745 Leinfelden-Echterdingen

Bosch Power Tools

GDX 14,4 V-LI

3 601 JB8 0..

-1

min

-1

min

¼" hexagon socket

Dr. Egbert Schneider

Senior Vice President

Engineering

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

16.11.2012

Assembly

Battery Charging

 Use only the battery chargers listed on the accessories

page. Only these battery chargers are matched to the lith-

ium ion battery of your power tool.

Note: The battery is supplied partially charged. To ensure full

capacity of the battery, completely charge the battery in the

battery charger before using your power tool for the first time.

The Lithium-Ion battery can be charged at any time without

reducing its service life. Interrupting the charging procedure

does not damage the battery.

The Lithium-Ion battery is protected against deep discharging

by the "Electronic Cell Protection (ECP)". When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

 Do not continue to press the On/Off switch after the

machine has been automatically switched off. The bat-

tery can be damaged.

The battery is equipped with a NTC temperature control

which allows charging only within a temperature range of be-

tween 0 °C and 45 °C. A long battery service life is achieved

in this manner.

Observe the notes for disposal.

Removing the battery

The battery 5 is equipped with two locking levels that should

prevent the battery from falling out when pushing the battery

unlocking button 6 unintentionally. As long as the battery is

inserted in the power tool, it is held in position by means of a

spring.

14.4

0 –2800

0 –3200

150*

170

M6 – M16

¼" hexagon socket

/ ½"

1.5/1.7*

Helmut Heinzelmann

Head of Product Certification

PT/ETM9

1 609 92A 00R | (12.12.12)

English | 15

GDX 18 V-LI

3 601 JB8 1..

0 –2800

0 –3200

160*

180

M6 – M16

/ ½"

1.6/1.8*