Bosch GBH 24 VRE Manual Petunjuk Asli - Halaman 12
Jelajahi secara online atau unduh pdf Manual Petunjuk Asli untuk Bor Bosch GBH 24 VRE. Bosch GBH 24 VRE 15 halaman. Bosch power tools hammer drill manual gbh 24 vfr, gbh 24 vre, gbh 24 vfr
Juga untuk Bosch GBH 24 VRE: Panduan Petunjuk Pengoperasian (11 halaman), Petunjuk Perbaikan (13 halaman)
Halaman Cetak
- 1. General Power Tool Safety Warnings
- 2. Machine-Specific Safety Warnings
- 3. Functional Description
- 4. Intended Use
- 5. Product Features
- 6. Technical Data
- 7. Declaration of Conformity
- 8. Battery Charging
- 9. Auxiliary Handle
- 10. Starting Operation
- 11. Maintenance and Service
- 12. Maintenance and Cleaning
24 | English
Reversing the Rotational Direction
Actuate the rotational direction switch 7
only when the machine is at a standstill.
The rotational direction switch 7 is used to re-
verse the rotational direction of the machine.
However, this is not possible with the On/Off
switch 8 actuated.
Right Rotation: For drilling and driving in
screws, push the rotational direction switch 7
left to the stop.
Left Rotation: For loosening and unscrewing
screws and nuts, press the rotational direction
switch 7 through to the right stop.
Switching On and Off
To start the machine, press the On/Off switch 8
and keep it depressed.
To switch off the machine, release the On/Off
switch 8.
For low temperatures, the machine reaches the
full hammer/impact capacity only after a certain
time.
This start-up time can be shortened by striking
the inserted tool insert against the floor one
time.
Setting the Speed/Impact Rate
The speed/impact rate of the switched on pow-
er tool can be variably adjusted, depending on
how far the On/Off switch 8 is pressed.
Light pressure on the On/Off switch 8 results in
low speed/impact rate. Further pressure on the
switch increases the speed/impact rate.
Run-on Brake
When the On/Off switch 8 is released, the chuck
brakes to a stop, thus preventing the run-on of
the tool.
When driving in screws, wait until the screw is
screwed in flush with the material and then re-
lease the On/Off switch 8. By doing so, the head
of the screw does not penetrate into the materi-
al.
1 619 929 740 | (24.7.07)
Overload Clutch
If the tool insert becomes caught or
jammed, the drive to the drill spindle is in-
terrupted. Because of the forces that occur,
always hold the power tool firmly with both
hands and provide for a secure stance.
If the power tool jams, switch the machine
off and loosen the tool insert. When switch-
ing the machine on with the drilling tool
jammed, high reaction torques can occur.
Operating Instructions
Do not operate the power tool stationary. It
is not designed for operation in a drill stand.
Inserting Screwdriver Bits (see figure I)
Apply the power tool to the screw/nut only
when it is switched off. Rotating tool inserts
can slip off.
To work with screwdriver bits, a universal bit
holder 22 with SDS-plus shank (accessory) is re-
quired.
Clean the shank end of the adapter shank and
apply a light coat of grease.
Insert the universal bit holder with a turning mo-
tion into the tool holder until it automatically
locks.
Check the locking effect by pulling the universal
bit holder.
Insert a screwdriver bit into the universal bit
holder. Use only screwdriver bits that match the
screw head.
Set the selector switch 6 to the "Drilling" sym-
bol.
To remove the universal bit holder, pull the lock-
ing sleeve 3 toward the rear and remove the uni-
versal bit holder 22 out of the tool holder.
Bosch Power Tools