Dremel 1671 Panduan Pemilik - Halaman 2
Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Melihat Dremel 1671. Dremel 1671 17 halaman. Type 2 scroll saw
Halaman Cetak
For
You
r
Safety
...
•
READ ALL
INSTRUCTION
S
Failure to follow the safety rules listed below and other
AWARNING
basic safety
preca uti
on
s
may result In serious personal injury.
W
ork
Area
•
KEEP W
ORK
AREAS
CLEAN. Cluttered areas and
benches
invite accidents.
•
M
A
KE WORKSHOP CH I
LD·PROOF-
wlth
padlocks,
aster switches. or by removing starter keys.
Pe
rso
na
I
S
afety
•
STAY
ALERT. Watch what you
are
doing. Use
com
mon
sense. Do not operate tool when you are
ti
red.
•
KEE
P
GUA
RDS
IN PLACE, in working order, and in
proper
adjustment and alignment.
• DON'T
OVER
REA
CH. Keep proper footing and
balance at all
Imes.
• DISCONNECT
TOOLS.
When not in use; before
servicing; when
c
langmg blades. bits, cutters, etc.
•
REMOVE ADJUSTIN
G
KEYS AND WRENC
H
ES
.
Form habit of chee
to
see
that keys and adjusting
wrenc
hes are removed
~rom
tool before turning it on.
•
N EVER STA
ND ON TOOL.
Se
riousinjurycouldoccur
If
the
tool IS tipped
or If
the
cutting tool is acci
dentally contacted.
•
AVOID
ACCI DENTAL
STARTING. Don't
carry
plugg
-
n
001
'h
finger
on switch. Be sure
s
ch
IS
OFF
en
plugg
ed
Tn.
•
USE RECOMMEND
EDACCESSORIE
S. Consultthe
owner's manual
for
recommended accessories.
Follow [he instructions th
at
accompany the
acces
sOries. The
use
of
improper
accessories
may
cause
hazards.
•
DRES
S
PROPERLY. Do not w ear
loose clothing or
jewelry.
They can be
caugh
t
in moving
parts. Rubber
gloves
and non-skid footwear are recommended
whe
n
working
outdoors. Wear
protective
hair
covering to contain long hair.
•
ALWAYS
USE
SA
FETY GLASSES. Also use face or
dust mask if cutting operation
is
dusty. Everyday
eyeg
lasses only have impact resistant lenses; they are
not
safet
y glasses.
All
repairs.
electrical or
mechanical.
AWARNING
should
be attempted
only
by
trained
repairmen.
Contact the
nearest Dr
mel
Service Center,
or AuthOrized
Dremel
Service
Station
or other com
petent repair service.
Use only Dremel replacement
parts; any other may
create
a
hazard.
• CHECK DAMAGED PARTS. Before further use of
e
001.
a guard or other part that is damaged
should
care
ully
checked to determine that it will operate
proper
and
perform
its intended
function.
Check for
alg
e
of moving
parts, binding
of
moving parts,
ea
ge
0
parts,
mount
ing, and any other conditions
- a ec
s
operation.
A
guard or other part
that
ed
s
00
d
be
properly repai red or
replaced.
SWitches
replaced. Do
not
ljse tool if
urn
It
on or off.
Tool Use
CE TOOL. It will do th
e
job
better
and
_
or which
it
was
designed.
TOOL Don
't
force sma
ll
tool or
Job of
a
heavy-dUty tool. Don't
OOfDC>se
no
Intended-for
example;
don't
c
mg tree limbs or
log s.
• SECURE
se lamps
or
a
vise
to hold
work.
It's safe
~
hand
and
it f mes bo
th
hands
OFFEED.
Feedworkm
oabladeorcu tter
agai nst
tn
of ro allan
of
the
blade
or
cutter
only.
• NEVER
LEAVE
TOOL
RUNNING UNATTENDED.
Turn pOVlier
• lea
e too
until it
comes
to
a
co
mplete
s
OP
• DO NOT ALTER
0
preciSion
bLJ
specified
IS
cond
ition.
• AVOID GASEOUS
tools
in
gaseo
s
th
ese tools
no
ignite
fumes.
•
M
AINTAIN TOOLS WITH CARE. Keep tools sharp
and
clean for
be e and safer
performance. Follow
instru
tions
for
ng and
changing accessories.
Inspect tool
cords
per
odically
and
jf
damaged, have
repaired
by
aut
eel
Service facility. I nspect exten
sion cords
per
00
cally
and replace if damaged
.
Keep
ha
ndles dry.
clean and free
from oi
l
and grease.
Before connecting the tool to
B
AWARNING
power source (receptacle, outlet.
etc.), be sure voltage supplied is the same as tha
t
specified on the
nameplate
of the tool. A power sou rce
With voltage greater than that specified for the tool
can
result
in
SERIOUS INJURY to the user, as well as
damage to
the
tool. If
in
doubt.
DO
NOT PLUG IN THE
TOOL.
USing a power
source
with voltage less than
the nameplate
rating
is
harmful
to
the motor.
"SAVE THESE INSTRUCTIONS"
Page 2