Electrolux ICON RH36WC60GS Panduan Penggunaan & Perawatan - Halaman 32

Jelajahi secara online atau unduh pdf Panduan Penggunaan & Perawatan untuk Kap Ventilasi Electrolux ICON RH36WC60GS. Electrolux ICON RH36WC60GS 44 halaman. 30” et 36” hotte aspirante
Juga untuk Electrolux ICON RH36WC60GS: Spesifikasi (2 halaman), Katalog Suku Cadang Pabrik (4 halaman), Panduan Pemasangan, Penggunaan & Perawatan (21 halaman), Panduan Pemasangan, Penggunaan & Perawatan (22 halaman), Panduan Pemasangan, Penggunaan & Perawatan (22 halaman), (Bahasa Inggris) Panduan Pemasangan, Penggunaan, dan Perawatan (22 halaman), (Bahasa Prancis) Panduan Pemasangan, Penggunaan, dan Pemasangan (22 halaman)

Halaman Cetak
Electrolux ICON RH36WC60GS Panduan Penggunaan & Perawatan
Installing the hood
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
Install supporlnstall framing for hood support
•
If drywall is present, mark the screw hole
locations. Remove the template.
•
Cut away enough drywall to expose 2 vertical
studs at the holes location indicated by the
template.
Install two horizontal supports at least 4 X 2"
between two wall studs at the bottom and upper
mounting holes installation location.
•
The horizontal support must be flush with the
room side of the studs.
•
Use cleats behind both sides of the support to
secure to wall studs.
°
Reinstalll drywall and refinish
IMPORTANT- Framing must be capable of
supporting 100 Ibs.
Mounting the hood
Install the 8" round transition as shows the image below.
The installation screws and the 8" round transition are
included on the hood package.
_
8 -1/2" min. opening for ductwork
View from rear
1" x 6" min
Mounting
Support
WARNING: 2 people are required to lift and position
the hood onto the mounting screws.
•
Place the template on the wall along the horizontal
line, make sure the template is leveled and
centered with the centerline.
•
Mark "upper" screw holes locations in the wall.
•
IMPORTANT. Check to be sure that hole locations
are leveled and correctly centered by the vertical
centerline.
•
Drive "upper" wood screws by hand. Leave 1A"of
distance between the screw head and the wall.
•
Remove the grease filter and mount the hood
onto the "upper" screws.
-.
J