Atlantic Ultraviolet MIN-6 Panduan Pemilik - Halaman 6

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Sistem Penyaringan Air Atlantic Ultraviolet MIN-6. Atlantic Ultraviolet MIN-6 16 halaman. Germicidal ultraviolet water purifiers
Juga untuk Atlantic Ultraviolet MIN-6: Panduan Pemilik (16 halaman), Panduan Pemilik (20 halaman)

Halaman Cetak

NSTALLATION

1. Remove water purifier from shipping carton. Inspect water purifier, power cord and plug for damage. Do not operate if

there is any damage to the purifier, power cord or plug. All models, of the MINIPURE

shipped with the lamps packed separately. Keep the lamp aside for installation once the purifier has been properly installed.

2. Units occasionally experience damage in shipment due to the fragility of the quartz sleeve. It is therefore

recommended to inspect the water purifier for damage to the quartz sleeve after it has been removed from the

shipping carton. Each end of the unit as well as the inlet and outlet should be viewed to see if the quartz sleeve has

experienced damage. If the quartz sleeve shows signs of damage it should be replaced before the purifier is

pressurized. See "QUARTZ SLEEVE CLEANING OR REPLACEMENT" in the "MAINTENANCE" section for the

proper method of replacing the quartz sleeve in your water purifier.

COMMON

PRE-TREATMENT or

PUMPING DEVICES

Incoming

1. Deionizer

Water

2. Water Softener

Supply

3. Carbon Filters (GAC)

4. Pressure Tank

5. Pump

6. Reverse Osmosis

7. Prefilters

Ultraviolet Water Purifiers

should be installed closest

to the point of use. (POU)

3. The water purifier should be mounted horizontally on a flat dry surface. The purifier should not be solely supported by its

plumbing connections. Securing the water purifier using the optional wall universal bracket kit is recommended.

4. The water purifier must be connected to the cold water line only.

5. It is recommended that a 5-micron sediment filter be installed, in line, prior to the water purifier. The sediment filter will

stop or trap any particulates from entering the water purifier. Particulates may cause damage to the quartz sleeve, as well

as interfere with the purifier's ability to disinfect the water. The sediment filter may also help to reduce the amount of

routine cleaning of the quartz sleeve.

6. Shut off valves should be installed on both the inlet and outlet sides of the water purifier. The use of bypass valves is not

recommended. The shut off valves allow the purifier to be isolated from the water supply, which is required when

removing the quartz sleeve.

7. Unions should be installed on both the inlet and outlet of the water purifier; this will allow easy removal of the water

purifier from the plumbing, if required. Apply Teflon ® tape to threads of inlet and outlet ports to ensure a tight seal.

8. When all plumbing connections are complete, allow water to enter the water purifier at a low flow rate, until the purifier is

pressurized. With the purifier pressurized, it should be checked for leaks. Once it is determined that there are no leaks, the

inlet valve can be fully opened.

9. Unpack the lamp and ballast. While holding lamp end, carefully push lamp socket on. Carefully slide lamp straight into

the quartz sleeve, without angling. Push the end cap on, over the static gland nut. Attach the ground connector to the

grounding tab of the chamber.

CAUTION: Lamp and quartz sleeve are easily damaged. Exercise care when installing lamp.

10. Plug ballast into an approved Ground Fault Circuit Interrupt (GFCI) receptacle. Where a 2-prong or unprotected 3-prong

receptacle is encountered, it must be replaced by a properly grounded Ground Fault Circuit Interrupt (GFCI) receptacle.

Installation must be in accordance with the National Electrical Code and any local codes and ordinances by a qualified

Electrician.

11. Once the plumbing hook ups are made, it is a good practice to disinfect the "downstream" plumbing. This is done by

introducing chlorine or other disinfectant solution directly into the purifier chamber, a 100-ppm of chlorine is suggested.

With the disinfectant solution in the purifier chamber, turn the ultraviolet purifier on. Open the "downstream" outlet until a

chlorine odor is noticed. Close the outlet and allow the disinfectant to remain in the plumbing for at least three (3) hours.

Flush the plumbing with ultraviolet purified water; allow the water to run for several minutes before use, this will allow

the ultraviolet lamp to reach its full germicidal output.

6 6

Figure 1 - Recommended Installation

Cold Water Line

OPTIONAL EQUIPMENT

Flow Control Valve

5 Micron

Filter

Valve

Union

Elbow

Ultraviolet

Water Purifier

OPTIONAL EQUIPMENT

Mounting Kit

line of water purifiers, are

POINT OF USE (POU)

Ultraviolet Water Purifiers

should be installed closest

to the point of use.

Outlet Line to point of use

to be as short as possible

Valve

Union

"X"

Recommended Minimum

Clearance for Lamp or

Quartz Sleeve Removal