Bosch 2 Panduan Pengguna dan Petunjuk Instalasi - Halaman 39

Jelajahi secara online atau unduh pdf Panduan Pengguna dan Petunjuk Instalasi untuk Penyedot Debu Bosch 2. Bosch 2 48 halaman. Mini blender
Juga untuk Bosch 2: Panduan Instalasi Cepat (16 halaman), Panduan untuk Instalasi dan Penggunaan (18 halaman), Manual Petunjuk Asli (13 halaman), Manual Petunjuk Asli (22 halaman), Buku Petunjuk (32 halaman), Panduan Pengguna (28 halaman), Panduan Pengguna dan Petunjuk Instalasi (16 halaman), Buku Petunjuk (42 halaman), Panduan Petunjuk Pengoperasian (8 halaman), Buku Petunjuk (8 halaman), Buku Petunjuk (12 halaman), Panduan Memulai Cepat (2 halaman), Panduan Memulai Cepat (9 halaman), Buku Petunjuk dan Petunjuk Instalasi (36 halaman), Panduan Petunjuk Pengoperasian (26 halaman), Panduan Referensi Cepat (2 halaman), Panduan Pengguna dan Petunjuk Instalasi (24 halaman), Buku Petunjuk (42 halaman), Informasi Untuk Penggunaan (28 halaman), Panduan Pengguna (40 halaman), Panduan Pengguna dan Petunjuk Instalasi (35 halaman), Panduan Pengguna (24 halaman)

Halaman Cetak
Bosch 2 Panduan Pengguna dan Petunjuk Instalasi
Fault
The programme dura-
tion changes during
the wash cycle.
No water is visible in
the drum.
Drum jerks after the
programme starts.
Residual water is
present in the com-
partment
.
Vibrations and move-
ment of the appliance
whilst spinning.
Drum rotates, water
does not flow in.
Heavy foam build-up
High spin speed not
reached.
Cause and troubleshooting
Foam detection system switches on a rinse cycle if
foam build-up is too high.
Not a fault – no action required.
▶
Water is below the visible area.
Not a fault – no action required.
▶
Do not add any extra water to the appliance while it
▶
is operating.
This is caused by an internal motor test.
Not a fault – no action required.
▶
Insert in compartment
→ "Cleaning the detergent drawer", Page 30
▶
Appliance is not correctly aligned.
→ "Aligning the appliance", Page 15
▶
The appliance feet are not fixed.
Secure the appliance feet.
▶
→ "Aligning the appliance", Page 15
Transit bolts have not been removed.
→ "Removing the transit bolts", Page 13.
▶
Load detection is active.
Not a fault – no action required.
▶
Note: The load detection can take up to two minutes.
Detergent dosage is too high.
Immediate measure: Mix one tablespoon of fabric
▶
softener with 0.5 litres of water and pour the mix-
ture into the left-hand compartment (not for outdoor
clothing, sportswear or items stuffed with down).
Reduce the amount of detergent for the next wash-
▶
ing cycle with the same load.
A low spin speed is selected.
The next time you run a wash cycle, set a higher
▶
spin speed.
Unbalance load detection system is using a reduced
spin speed to eliminate an unbalance.
Redistribute the laundry in the drum.
▶
Note: Where possible, mix large and small items in
the drum. Different sized items of laundry distribute
themselves better during the spin cycle.
Start the Spin programme.
▶
Troubleshooting en
is blocked.
39