Bosch 4 V-LI Manual Petunjuk Asli - Halaman 10

Jelajahi secara online atau unduh pdf Manual Petunjuk Asli untuk Penyedot Debu Bosch 4 V-LI. Bosch 4 V-LI 15 halaman. Professional
Juga untuk Bosch 4 V-LI: Petunjuk Manual (31 halaman), Manual Petunjuk Asli (7 halaman), Manual Petunjuk Asli (10 halaman), Manual Petunjuk Asli (7 halaman), Manual Petunjuk Asli (48 halaman), Manual Petunjuk Asli (14 halaman)

Halaman Cetak

OBJ_BUCH-1257-001.book Page 22 Thursday, July 15, 2010 9:04 AM

22 | English

Battery Charge-control Indication

(only for 3.0 Ah battery) (see figure A)

The three green LEDs of the battery charge-con-

trol indicator 16 indicate the charge condition of

the battery 3. For safety reasons, it is only pos-

sible to check the status of the charge condition

when the machine is at a standstill.

Press button 15 to indicate the charge condi-

tion. This is also possible when the battery 3 is

removed.

LED

Continuous lighting 3 x green

Continuous lighting 2 x green

Continuous lighting 1 x green

Flashing light 1 x green

When no LED lights up after pushing button 15,

then the battery is defective and must be replaced.

Replacing/Inserting the Saw Blade

When mounting the saw blade, wear protec-

tive gloves. Danger of injury when touching

the saw blade.

Selecting a Saw Blade

An overview of recommended saw blades can

be found at the end of these instructions. Use

only T-shank saw blades. The saw blade should

not be longer than required for the intended cut.

Use a thin saw blade for narrow curve cuts.

Inserting the Saw Blade (see figure B)

Clean the shank of the saw blade before in-

serting it. An unclean shank cannot be fas-

tened securely.

Insert the saw blade 11 into the stroke rod 17

until it latches. The SDS lever 12 automatically

snaps to the rear and the saw blade is locked.

Do not manually press the lever 12 toward the

rear, otherwise you could damage the machine.

While inserting the saw blade, pay attention that

the back of the saw blade is positioned in the

groove of the guide roller 9.

Check the tight seating of the saw blade. A

loose saw blade can fall out and lead to inju-

ries.

1 609 929 W85 | (15.7.10)

Ejecting the Saw Blade (see figure C)

When ejecting the saw blade, hold the ma-

chine in such a manner that no persons or

animals can be injured by the ejected saw

blade.

Turn the SDS lever 12 forward towards the con-

tact protector 13 to the stop. The saw blade is

released and ejected.

Dust/Chip Extraction

Dusts from materials such as lead-containing

Capacity

coatings, some wood types, minerals and

≥2/3

metal can be harmful to one's health. Touch-

≥1/3

ing or breathing-in the dusts can cause aller-

gic reactions and/or lead to respiratory infec-

<1/3

tions of the user or bystanders.

Reserve

Certain dusts, such as oak or beech dust, are

considered as carcinogenic, especially in

connection with wood-treatment additives

(chromate, wood preservative). Materials

containing asbestos may only be worked by

specialists.

– As far as possible, use a dust extraction

system suitable for the material.

– Provide for good ventilation of the work-

ing place.

– It is recommended to wear a P2 filter-

class respirator.

Observe the relevant regulations in your

country for the materials to be worked.

Prevent dust accumulation at the work-

place. Dusts can easily ignite.

Connecting the Dust Extraction

(see figures D–E)

Insert the vacuum connection 18 into the open-

ing of base plate 7.

Place a vacuum hose 19 (accessory) onto the

vacuum connection 18. Connect the vacuum

hose 19 with a vacuum cleaner (accessory). An

overview for the connection of various vacuum

cleaners can be found at the end of these in-

structions.

To enable optimum dust extraction, use the

splinter guard 20 if possible.

Bosch Power Tools