Atlas CP700 Panduan Pemilik - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Penguat Atlas CP700. Atlas CP700 16 halaman. Commercial dual channel power amplifiers
Juga untuk Atlas CP700: Brosur (2 halaman), Panduan Pemilik (16 halaman), Panduan Pemilik (16 halaman), Lembar Spesifikasi (2 halaman), Brosur & Spesifikasi (10 halaman), Panduan Pemilik (16 halaman)

Halaman Cetak
Atlas CP700 Panduan Pemilik
Commercial Power Amplifier

FrONT PANEL DESCrIPTION

2
3
1. Power Switch
This rocker switch supplies power to the amplifier. A red LED located above the power
switch will illuminate when the amplifier is switched on.
2. Protect LED Indicators
The amplifier features several types of protection circuitry to prevent damage during
power-up or fault conditions. If any of these LEDs illuminate, one of the various protection
features is safeguarding the amplifier. The output relays will disconnect the speaker loads when
the protection circuitry detects a fault condition.
• Loudspeaker Protection - When power is first applied, the speaker protection relay is
open, preventing transients from reaching the loudspeakers. After the internal power
supplies have stabilized, the relay will close, connecting the amplifier output to the load.
The yellow Protect LEDs will illuminate during this power-up process.
• Thermal Protection - The amplifier protection circuitry monitors itself for excessive
internal operating temperatures. In the event this circuitry detects abnormal thermal
conditions (blocked cooling fan or high ambient temperatures), the speaker relay
will disconnect the speaker load from the amplifier. Once the internal operating
temperature drops back to a safe level, the relay will close, reconnecting the speaker load
to the amplifier.
• Short Circuit Protection - The yellow Protect LEDs will illuminate should the amplifier
detect a short circuit on the attached speaker load or if the load impedance is too low.
When this condition is detected, the internal speaker relays will open up, disconnecting
the load from the amplifier. The protection circuitry will stay activated until the fault is
cleared.
Note: Once the specific fault has been corrected, the power may have to be cycled to reset the
protection circuitry.
3. Signal "Status" LED Indicator
The green "Status" LEDs will illuminate once the input signal has reached -26 dBV or higher.
AtlasSound.com
CP400 & CP700
PROTECT
PROTECT
LIMIT
LIMIT
SIGNAL
SIGNAL
CH-1
CH-2
4
CH-1
CH-1
8, 4, and 2 Ohms
AUDIO TRANSFORMER
CP700
+
-
0
70
100
D I R . O U T P U T
I S O L . O U T P U T
Commercial
Power
Amplifier
Per Channel
-
+
-
+
Output Power
+
70V
25V
400 W / 4 Ohms
BRIDGE
350 W / 70.7 V
MONO
- 100V +
CH-2
CH-2
8, 4, and 2 Ohms
AUDIO TRANSFORMER
+
-
0
70
100
D I R . O U T P U T
I S O L . O U T P U T
AC100V-50/60Hz
AC120V-50/60Hz
AC230V-50/60Hz
AC240V-50/60Hz
-
+
-
+
-
70V
25V
BRIDGE
MONO
- 100V +
POWER
MADE IN CHINA
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
AVIS RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
NO USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.
Specifications are subject to change without notice.
CP700
Commercial Power Amplifier
IN
THRU
GND
Telephone: 800.876.3333 • Fax: 800.765.3435
– 4 –
Owner's Manual
POWER
Figure 1
IN
AMPLIFIER INPUTS
CH-2
CH-1
+
-
GND
-
+
THRU
LEVEL
LEVEL
STEREO
PARALLEL
BRIDGE
1601 Jack McKay Blvd., Ennis, TX 75119
(800) 876-3333 AtlasSound.com
1