Advanced Power Systems 625VA Panduan Pengguna - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk UPS Advanced Power Systems 625VA. Advanced Power Systems 625VA 2 halaman.

Halaman Cetak

FRONT PANEL EXPLANATIONS

1. Line LED (

Green LED remains standstill when Utility is

normal.

Green LED flashes every 3 seconds and

simultaneously buzzer alarms continuously

when Utility failure.

Green LED flashes every 3 seconds when the

UPS is in Battery charging mode.

Green LED remains standstill and

simultaneously buzzer alarms continuously

when the UPS is in overload condition.

2. Check Battery LED (

Red LED flashes every 0.5 seconds and

buzzer alarms every 0.5 seconds when UPS

is in battery low condition.

3. Main Switch:

a. To Control on/off the UPS when Utility is normal.

b. To enable "DC-Start" Function when Utility fails. (To enable DC Start

properly, you are recommended to connect <80% output load with the

UPS only)

P.S. Make sure the computer connected to the UPS is switched on before

enable the "DC-Start" function. You are not recommended to add some

other computer or peripherals after DC-Start function is activated.

Note: Once the battery is disconnected,

the loads are not protected from power

outages.

1. Use a cross-type screwdriver to remove the

two front panel screws and slide down the

panel.

2. Gently Pull the battery out of the UPS.

3. Loosen the black wire from the negative (-)

terminal and red wire from the positive (+)

terminal.

4. Connect the battery leads to the new battery.

5. Note: Small sparks at the battery connectors

are normal during connection.

6. Slide the battery into the UPS.

7. Close the front panel and fasten two screws.

8. Dispose of the old battery properly at an

appropriate recycling facility.

When your UPS malfunctions during operation, you may check the list below for proper adjustment. If the adjustment still be in vain,

please contact your sales agent for help.

Situation

Mains normal but 'Line' LED is not on.

'Line' LED flashes every second but no

output

Alarm buzzer beeps continuously when

Utility is normal.

Alarm buzzer beeps for 10 seconds, then

the UPS is turned off

No LEDs display on the front panel

UPS dose not provide expected back up

time.

The UPS operates normally, but the site

wiring fault indicator is lit.

Seite 2 von 2,

REPLACING THE BATTERY

TROUBLE SHOOTING

1. Is the power switch on?

2. Is the fuse in order?

3. Is the power cord loose?

Battery voltage is too low

Check to see load status if it is in overload.

1. The UPS's battery is weak due to recent

outage.

2. The UPS's battery is near the end of its

service life.

Building wiring error such as missing ground or

hot to neutral wire reversal.

Advanced Power Systems GmbH & Co. KG, Bayreuther Str. 6, D-91301 Forchheim

REAR PANEL EXPLANATIONS

1. AC Inlet

2. Backup Outlets: 3pcs NEMA5-15R or IEC320

3. Computer Interface: True RS232 communication port.

4. RJ11/RJ45 Jacks: MODEM /LAN Protection

5. Site Wiring Fault Indicator: For 115Vac system only.

6. AC Fuse Holder. (W/fuse)

525VA/115Vac/6A

525VA/230Vac/4A

625VA/115Vac/8A

625VA/230Vac/6.5A

Check Items

800VA/115Vac/8A

800VA/230Vac/6.5A

Solution

1. .Press Main Switch on.

2. Change fuse w/same rating.

3. Re-connect the power cord properly.

Recharge the UPS for 24 hours.

Remove some uncritical load.

Remove some uncritical load and re-switch

on the UPS.

Consult with your sales agent For help.

1. Charge the battery.

2. If the battery is near the end of its service

lift, consider replacing the battery.

Have a qualified electrician correct the

building wiring.