Bose Lifestyle 28 Panduan Pemecahan Masalah - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Pemecahan Masalah untuk Pembicara Bose Lifestyle 28. Bose Lifestyle 28 32 halaman. Dvd home entertainment systems
Juga untuk Bose Lifestyle 28: Panduan Instalasi (32 halaman), Panduan Pengoperasian (44 halaman), Panduan Pemilik (22 halaman), Panduan Pengoperasian (46 halaman), Panduan Pengoperasian (44 halaman), Panduan Pengoperasian (34 halaman)

1. Parts that have special safety characteristics are identified by the symbol on

or by special notes on the parts list. Use only replacement parts that have critical characteristics

recommended by the manufacturer.

2. Make leakage current or resistance measurements to determine that exposed parts are accept-

ably insulated from the supply circuit before returning the unit to the customer. Use the following

checks to perform these measurements:

A. Leakage Current Hot Check-With the unit completely reassembled, plug the AC line cord

directly into a 120V AC outlet. (Do not use an isolation transformer during this test.) Refer to

UL6500 paragraph 9.1.1. Use a leakage current tester or a metering system that complies with

American National Standards Institute (ANSI) C101.1 "Leakage Current for Appliances" and

Underwriters Laboratories (UL) 6500, IEC 60065 paragraph 9.1.1. With the unit AC switch first in

the ON position and then in OFF position, measure from a known earth ground (metal waterpipe,

conduit, etc.) to all exposed metal parts of the unit (antennas, handle bracket, metal cabinet,

screwheads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer

an electrical return path to the chassis. Any current measured must not exceed 0.5 milliamp.

Reverse the unit power cord plug in the outlet and repeat test. ANY MEASUREMENTS NOT

WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT

MUST BE ELIMINATED BEFORE RETURNING THE UNIT TO THE CUSTOMER.

B. Insulation Resistance Test Cold Check-(1) Unplug the power supply and connect a jumper

wire between the two prongs of the plug. (2) Turn on the power switch of the unit. (3) Measure the

resistance with an ohmmeter between the jumpered AC plug and each exposed metallic cabinet

part on the unit. When testing 3 wire products, the resistance measured to the product enclosure

should be between 2 and infinite Meg ohms. Also, the resistance measured to exposed output/

input connectors should be between 4 and infinite Meg ohms. When testing 2 wire products, the

resistance measured to exposed output/input connectors should be between 4 and infinite Meg

ohms. If it is not within the limits specified, there is the possibility of a shock hazard, and the unit

must be repaired and rechecked before it is RETURNED TO THE CUSTOMER.

ELECTROSTATIC DISCHARGE SENSITIVE (ESDS)

This unit contains ESDS devices. We recommend the following precautions when repairing,

replacing or transporting ESDS devices:

• Perform work at an electrically grounded work station.

• Wear wrist straps that connect to the station or heel straps that connect to conductive floor mats.

• Avoid touching the leads or contacts of ESDS devices or PC boards even if properly grounded.

Handle boards by the edges only.

• Transport or store ESDS devices in ESD protective bags, bins, or totes. Do not insert unpro-

tected devices into materials such as plastic, polystyrene foam, clear plastic bags, bubble wrap or

plastic trays.

CAUTION: THE BOSE

VICEABLE PARTS. TO PREVENT WARRANTY INFRACTIONS, REFER SERVICING TO

WARRANTY SERVICE STATIONS OR FACTORY SERVICE.

SAFETY INFORMATION

DEVICE HANDLING

PS 28 AND PS 35 POWERED SPEAKER CONTAINS NO USER-SER-

PS18/28/35 Troubleshooting Guide

schematics