Bose VCS-10 Panduan Pemilik - Halaman 8
Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Pembicara Bose VCS-10. Bose VCS-10 35 halaman. Bose vcs-10: owners guide
Juga untuk Bose VCS-10: Panduan Pemilik (18 halaman), Panduan Pemilik (17 halaman), Panduan Pemilik (15 halaman)
Halaman Cetak
Connect
the speakers
A
CAUTION:
Before making any connections, turn off your receiver
or amplifier and unplug it from the AC power (mains) outlet. Not
doing so may result in damage to your system.
A
CAUTION: Never use broken or frayed wiring, which can result in
damage to your components.
P Note: Before running speaker cord through a wall or under a floor;
check your local building code requirements and safety regula-
tions. You may want to contact an electrical installer for this infor-
ma tion.
If your receiver's center channel is not amplified, you must con-
nect an amplifier to the receiver. Use an RCA cable to connect the
center channel RCA-type output on the receiver to the RCA-type
input on the amplifier. The speaker will then connect directly to the
amplifier instead of to the receiver.
Choosing
speaker
cord
Be sure to use the proper gauge (thickness) of speaker cord. Stan-
dard zip cord (2-conductor, 18-gauge wire found at electrical and
hardware stores) works for most applications. If your speakers will
be more than 30 feet (9 m) from the receiver or amplifier, see the
following table, or check with your authorized Bose dealer.
Gauge*
Length*
18 (0.75
mm')
30
ft (9 m) maximum
16 (1.5 mm*)
45 f? (14 m) maximum
14 (2.0 mm2)
70 ft (21 m) maximum
* Based on a maximum frequency response deviation of 50.5dB.
At the end,s of each cord, strip approximately 112 inch (12 mm) of
insulation from both wires. Twist the bare end of each wire, so
loose strands will not touch across terminals.
Be sure to use the cord properly
Speaker cord consists of two insulated wires. The insulation
around one wire is marked (striped, collared, or ribbed). This
marked wire is always positive (+). The plain wire is always nega-
tive (-). These wires correspond to the red (+) and black (-) termi-
nals on the speaker and the receiver or amplifier.
P Note: It is sometimes difficult to distinguish wire markings.
Inspect both wires carefully
8
Connect the speakers
it..
CAUTION: Before making any connections, turn off your receiver
or amplifier and unplug it from the AC power (mains) outlet. Not
doing so may result in damage to your system.
it..
CAUTION: Never use broken or frayed wiring, which can result in
damage to your components.
) Note: Before running speaker cord through a wall or under a floor,
check your local building code requirements and safety regula-
tions. You may want to contact an electrical installer for this infor-
mation.
If your receiver's center channel is not amplified, you must con-
nect an amplifier to the receiver. Use an RCA cable to connect the
center channel RCA-type output on the receiver to the RCA-type
input on the amplifier. The speaker will then connect directly to the
amplifier instead of to the receiver.
Choosing speaker cord
Be sure to use the proper gauge (thickness) of speaker cord. Stan-
dard zip cord (2-conductor, 18-gauge wire found at electrical and
hardware stores) works for most applications. If your speakers will
be more than 30 feet (9 m) from the receiver or amplifier, see the
following table, or check with your authorized Bose dealer.
Gauge
*
18 (0.75 mm')
16 (1.5
mm')
14 (2.0
mm')
Length
*
30 ft (9 m) maximum
45
ft
(14
m) maximum
70 ft (21 m) maximum
*
Based on
a
maximum frequency response deviation of ±O.5dB.
At the ends of each cord, strip approximately
112
inch (12 mm) of
insulation from both wires. Twist the bare end of each wire, so
loose strands will not touch across terminals.
Be sure to use the cord properly
Speaker cord consists of two insulated wires. The insulation
around one wire is marked (striped, collared, or ribbed). This
marked wire is always positive (+). The plain wire is always nega-
tive (-). These wires correspond to the red (+) and black (-) termi-
nals on the speaker and the receiver or amplifier.
) Note:
It is sometimes difficult to distinguish wire markings.
Inspect both wires carefully