Bose PROFLIGHT Series 2 Petunjuk Perakitan - Halaman 2
Jelajahi secara online atau unduh pdf Petunjuk Perakitan untuk Headset Bose PROFLIGHT Series 2. Bose PROFLIGHT Series 2 2 halaman. Aviation headset
Juga untuk Bose PROFLIGHT Series 2: Panduan Memulai Cepat (4 halaman), Panduan Pertanyaan yang Sering Diajukan (15 halaman)
Halaman Cetak
Refer to the Bose ProFlight Series 2 Aviation Headset
• Do NOT make phone calls while piloting.
owner's guide accompanying your Bose ProFlight Series 2
Do not use the headset for telephone calls during
Aviation Headset for more information. To request a printed
flight operations.
copy, contact Bose customer service.
• Make sure your aircraft communications system volume
Visit: worldwide.Bose.com/Support/ProFlight2
control is easily accessible.
Important Safety Instructions
This control affects the strength of the communications
signal coming into the headset. Make sure you can
WARNINGS/CAUTIONS
understand critical communications even with Acoustic
Noise Canceling mode turned off. In this case, you may need
• Do NOT use the headphones with noise canceling mode
to turn up the aircraft communications system volume. In
at any time the inability to hear surrounding sounds may
passive mode, the volume controls on the control module
present a danger to yourself or others, e.g., while riding a
will automatically be set to maximum volume. For additional
bicycle or walking in or near traffic, a construction site or
volume control, use the intercom or radio volume control.
railroad, etc.
If your headset is aircraft powered, connect the headset to
• Keep batteries out of reach of children.
the aircraft power sources only as described in the Bose
• Please dispose of used batteries properly, following any
ProFlight Series 2 Aviation Headset owner's guide.
local regulations.
• Make sure portable devices do not interfere with the
• Danger of explosion if batteries are incorrectly replaced.
aircraft's navigation and communication systems.
• Batteries may cause a fire or chemical burn if mishandled.
It is the pilot's responsibility to ensure that portable
Do not recharge, disassemble, heat, or incinerate.
devices do not interfere with the aircraft's navigation and
• When a replacement is needed, use only a AA (LR06)
communication systems, as well as to determine if the
alkaline batteries.
portable device is suitable for use with the headset.
Please read and save this guide
• Use only AA alkaline batteries.
To avoid risk of explosion, replace the batteries only with
Please read this guide carefully. Save this guide for future
reference and make it easily accessible for passengers and
AA alkaline batteries. Properly dispose of used batteries.
third parties who use this headset.
• Do NOT repair the headset yourself.
• Switch to an alternate communications method in the
Contact the Bose organization in your country/region for
event of a headset issue.
specific care, return and shipping instructions.
In the unlikely event of any headset issue or failure in
Visit: global.Bose.com
the passive noise reducing mode, switch to an alternate
• Do not use the headset with a helmet or as part of a crash
communications method and use standard cockpit resource
protection system.
management skills to minimize distractions.
The headset is not intended for such use, and has not been
• Use the headset at a moderate volume level.
certified for crash protection. Dismantling, reassembly or
To avoid hearing damage, use the headset at a comfortable,
modification of the headset, or any part, for use in a helmet
moderate volume level. Limit the headset volume to
or other crash protection system could result in severe
safe levels that do not interfere with your ability to hear
bodily injury and such unauthorized use will void the limited
informational sounds and warning alarms, such as stall
product warranty.
warnings or gear up, while piloting.
• Do NOT immerse the headset or any parts in water or any
• Turn the headset off if it emits any loud noise.
other liquid.
As with any complex electronic device, it is possible for this
See the Bose ProFlight Series 2 Aviation Headset owner's
headset to fail during operation. Symptoms of failure, which
guide for cleaning instructions.
may include loud tones, distortion, feedback squeals and
loss of communications signal in the headset, can occur in
Contains small parts which may be a choking hazard.
either the Acoustic Noise Cancelling mode (turned on) or
Not suitable for children under age 3.
in the passive mode (turned off). If the headset emits any
loud noise and the related loss of communications in the
This product contains magnetic material. Consult
Acoustic Noise Cancelling mode, turn off the power switch.
your physician on whether this might affect your
The headset will continue to provide communications in the
implantable medical device.
passive noise-reducing mode. If the problem persists, see
the Troubleshooting section in the Bose ProFlight Series 2
• Do NOT expose this product to dripping or splashing, and
Aviation Headset owner's guide.
do not place objects filled with liquids, such as vases, on or
near the product.
• Be aware of sound differences while wearing the headset.
• Do NOT make unauthorized alterations to this product.
With the headset's active and passive noise reduction, typical
• Do not expose products containing batteries to excessive
aircraft sounds (such as engines, propellers, warning alarms,
heat (e.g. from storage in direct sunlight, fire or the like).
and other sound sources) may not sound familiar. Make sure
you can hear and recognize these sounds when using the
headset while operating any aircraft.
The microphone assembly can be easily
attached to the left or right side of the
Bose ProFlight Series 2 Aviation Headset.
NOTE: The headset ships with the terminator
cover attached to right side. To attach
the microphone assembly to the right
side of the headset, you must first
remove the terminator cover and
attach it to the left side of the headset.
MOVE THE TERMINATOR COVER
1. Push the release button into the release button
opening, and gently pull the terminator cover
from the connector socket.
2. On the other side of the headset, align the
release button to the release button opening,
and insert the terminator cover into the base
of the connector socket.
3. Slide the terminator cover into the connector
socket until the release button is secure.
CAUTION: Do NOT force the terminator cover
into the connector socket.
NOTE: If the terminator cover is not securely
installed, there will be no audio coming
from that earbud.
CONNECT THE MICROPHONE
1. Align the release button to the
release button opening, and insert
the microphone connector into the
base of the connector socket.
Release button
opening
Connector socket
Terminator cover
Release button
2. Slide the microphone connector into the
connector socket until the release button
is secure.
CAUTION: Do NOT force the
3. Test the headset before flight.
microphone assembly into
the connector socket.