Daikin BRC7FB532F Panduan Pengoperasian - Halaman 4
Jelajahi secara online atau unduh pdf Panduan Pengoperasian untuk Kontrol Jarak Jauh Daikin BRC7FB532F. Daikin BRC7FB532F 12 halaman. Wireless remote controller kit
Halaman Cetak
Names and functions of the operating
section
See figure 1, (figure 1B shows the remote controller with
front cover opened)
1
DISPLAY "
" (SIGNAL TRANSMISSION)
This lights up when a signal is being transmitted.
2
DISPLAY "
" "
" "
MODE)
This display shows the current OPERATION MODE.
3
DISPLAY "
" (SET TEMPERATURE)
This display shows the set temperature.
4
DISPLAY "
This display shows PROGRAMMED TIME of the
system start or stop.
5
DISPLAY "
" (SWING FLAP)
Refer to "AIR FLOW DIRECTION ADJUST" on
page 5.
6
DISPLAY "
" "
The display shows the set fan speed.
7
DISPLAY "
" (INSPECTION/ TEST OPERA-
TION)
When
the
INSPECTION/TEST
BUTTON is pressed, the display shows the system
mode is in.
8
ON/OFF BUTTON
Press the button and the system will start. Press the
button again and the system will stop.
9
FAN SPEED CONTROL BUTTON
Press this button to select the fan speed, HIGH or
LOW, of your choice.
10 TEMPERATURE SETTING BUTTON
Use this button for SETTING TEMPERATURE
(Operates with the front cover of the remote controller
closed.)
11 PROGRAMMING TIMER BUTTON
Use this button for programming "START and/or
STOP" time. (Operates with the front cover of the
remote controller opened.)
12 TIMER MODE START/STOP BUTTON
Refer to "TIMER MODE START/STOP" on page 6.
13 TIMER RESERVE/CANCEL BUTTON
Refer to "PROGRAMMING TIME" on page 6.
14 AIR FLOW DIRECTION ADJUST BUTTON
Refer to "AIR FLOW DIRECTION ADJUST" on
page 5.
15 OPERATION MODE SELECTOR BUTTON
Press this button to select OPERATION MODE.
Operation manual
2
" "
" "
" (OPERATION
"(PROGRAMMED TIME)
" (FAN SPEED)
OPERATION
4P563995-1 2019.01
16 FILTER SIGN RESET BUTTON
Refer to the section of MAINTENANCE in the
operation manual attached to the indoor unit.
17 INSPECTION/TEST OPERATION BUTTON
This button is used only by qualified service persons
for maintenance purposes.
See figure 3, (receiver on decoration panel)
18 EMERGENCY OPERATION SWITCH
This switch is readily used if the remote controller
does not work.
19 RECEIVER
This receives the signals from the remote controller.
20 OPERATING INDICATOR LAMP (Red)
This lamp stays lit while the air conditioner runs. It
flashes when the unit is in trouble.
21 TIMER INDICATOR LAMP (Green)
This lamp stays lit while the timer is set.
22 AIR FILTER CLEANING TIME INDICATOR LAMP
(Red)
Lights up when it is time to clean the air filter.
23 DEFROST LAMP (Orange)
Lights up when the defrosting operation has started.
See figure 4, (cool/heat changeover switch)
In a VRV system, the wireless remote controller can be
used together with a cool/heat changeover switch.
24 FAN/AIR CONDITIONING SELECTOR SWITCH
Set the switch to "
(A/C) for HEAT or COOL.
25 COOL/HEAT CHANGEOVER SWITCH
Set the switch to "
(HEAT) for HEAT
NOTE
■ For the sake of explanation, all
indications are shown on the display in
figure 1 contrary to actual running
situations.
■ If the air filter cleaning time indicator
lamp lights up, clean the air filter as
explained in the operation manual
provided with the indoor unit.
After cleaning and reinstalling the air
filter, press the filter sign reset button
on the remote controller. The air filter
cleaning time indicator lamp on the
receiver will go out.
■ The defrost lamp will flash when the
power is turned on. This is not a
malfunction.
BRC7FA532F(B) + BRC7FB532F(B)
" (FAN) for FAN and "
" (COOL) for COOL and "
Wireless remote controller kit
"
"