Daintree GE current Tetra PowerStrip Snap DS Panduan Instalasi - Halaman 8
Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Peralatan Pencahayaan Daintree GE current Tetra PowerStrip Snap DS. Daintree GE current Tetra PowerStrip Snap DS 8 halaman. Led lighting system
Halaman Cetak
Tetra
PowerStrip Snap DS
®
Troubleshooting
Symptom
Row of modules does not light
Sign does not light
Individual modules do not light
Modules are dim
Maximum Loading per Tetra
SKU
Rating
GEDS71-3
GEDS65-3
GEDS57-3
24VDC
GEDS50-3
2.59W/module
GEDS41-3
GEDS32-3
Maximum Remote Mounting Distance
25W Power Supply
80W Power Supply
100W Power Supply
180W Power Supply
300W Power Supply
If you have any questions about these instructions or your specific application, please contact support at [email protected].
This product is intended solely for the use of non-residential signage lighting and is not intended for use in any other applications.
LED modules are not suitable for prolonged submersion or direct exposure to water and must be protected from the weather.
Solution
•
Check wire connections to power supply to ensure red stripe-to-red and white-to-black or
blue connections.
•
Check row-to-row polarity connections.
•
Check input and output voltage and check power supply input/output connections.
•
Check polarity connections.
•
Ensure the overall length of the Tetra® LED System does not exceed the maximum load.
•
Remove module and replace with another working module.
•
Ensure the overall length of the Tetra
•
Ensure the length and gauge of the supply wire is equal to or below the recommended
remote mounting distance.
®
25W
80W
Power Supply
Dimming Power Supply
Note: Load shall
Note: Load shall
not exceed 1.04A
not exceed 3.3A
8 modules
26 modules
18 AWG/0.82 mm
Supply Wire
120 ft./36.6 m
20 ft./6.1 m
20 ft./6.1 m
20 ft./6.1 m
20 ft./6.1 m
Conforms to the following standards: IP66.
Acceptable for use in dry and damp locations
The suitability of rain enclosure shall be determined if intended for wet location.
www.gecurrent.com
© 2020 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the
General Electric Company and are used under license. Information provided is subject to change without
notice. All values are design or typical values when measured under laboratory conditions.
SIGN271 (Rev 06/11/20) Enovia - A-1025384
LED system does not exceed the maximum load.
®
24 VDC Class 2 Power Supply
100W
Power Supply
Note: Load shall not
Note: Load shall not
exceed 4A per each
exceed 4.0A
(of 2) output channels
32 modules
16 AWG/1.31 mm
14 AWG/2.08 mm
2
2
Supply Wire
–
25 ft./7.6 m
25 ft./7.6 m
25 ft./7.6 m
25 ft./7.6 m
Installation Guide
180W
300W
Power Supply
Power Supply
Note: Load shall not
exceed 4A each (of 3)
output channels
29 modules per
32 modules per
output channel
output channel
58 modules per
96 modules per
power supply
power supply
12 AWG/3.31 mm
2
Supply Wire
Supply Wire
–
–
35 ft./10.6 m
40 ft./12.1 m
35 ft./10.6 m
40 ft./12.1 m
35 ft./10.6 m
40 ft./12.1 m
35 ft./10.6 m
40 ft./12.1 m
2