Daintree GE Current Lumination Tetra Contour 75485 Series Panduan Instalasi - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Lampu luar ruangan Daintree GE Current Lumination Tetra Contour 75485 Series. Daintree GE Current Lumination Tetra Contour 75485 Series 7 halaman.

Halaman Cetak
Lumination
(Tetra
®
Installation
Light engine (back)
Light engine (back)
Light engine (back)
Wire loops
Wire loops
Wire loops
Light guide
Light guide
Light guide
7
Wires between light guide
segments can be folded behind
the light guide and attached with
clear zip ties. Zip ties should wrap
around outside light guide.
RISK OF FIRE: Waterproof wire connection and all cut ends for outdoor or wet installations. Weather box is required for all outdoor
or wet locations electrical connections. / RISQUE D'INCENDIE: Étanchéifier les connexions électriques et sceller l'extrémité
des sections coupées effectuées à l'extérieur ou pour un environnement exposé à l'eau. Un boitier étanche est requis pour les
connexions électriques effectuées à l'extérieur ou dans un environnement avec exposition à l'eau.
Weather box
can be painted
Cut end:
separate wires
10
Insert wire connectors into
weather box. Fill with electrical
grade silicone and close box.
Weather box can be mounted
using #8 (M3) screws.
Joining with Light Guide Connectors, Corners and Bends
Electrical grade
Electrical grade
silicone
Electrical grade
silicone
silicone
13
Linear: At each gap between
sections, apply silicone on both
sides to secure light guide
connector. Snap on a light guide
connector.
RISK OF FIRE: DO NOT bend the light engine to an inside radius that is tighter than 3/4 in. (19mm).
RISQUE D'INCENDIE: Ne pas plier les modules DEL Contour avec un rayon de courbure inférieur à 3/4 pouce (19 mm).
Contour - Series)
®
Separate wires
+ – +
+ – +
8
To connect two light engines
separate wires and identify outer
conductors as positive (+) and
middle conductors as negative (–).
Strip ends back 0.5 in. (13mm).
WARNING / AVERTISSEMENT
Weather box
Electrical
can be painted
grade
silicone
Cut end:
separate wires
11
For cut end, manually untwist and
separate wires to avoid shorts. Fill
cap with electrical grade silicone
and push cap on the end to seal.
Clean excess silicone.
Electrical
Electrical
Electrical
grade
grade
grade
silicone
silicone
silicone
14
Corner: For all corners (planar,
inside, outside) apply silicone on
both sides to secure light guide
corners. Snap on corner. Follow
Steps 8-10 if wires are cut.
WARNING / AVERTISSEMENT
Separate wires
Separate wires
+
+
+
–
–
+ – +
–
+
+
+
Wire
Wire
Wire
Do not
Do not
Do not
bend one
bend one
bend one
light into a
light into a
light into a
corner
corner
corner
4
Installation Guide
Connect four
Connect two
Connect two
Connect four
Connect two
Connect four
positives (+)
negatives (–)
positives (+)
negatives (–)
positives (+)
negatives (–)
9
Use twist-on wire connectors to
join wires together.
Electrical
grade
silicone
Cut end:
separate wires
12
For uncut end, fold wire over Tetra
Contour. Fill the end cap with
silicone and push cap on the end to
secure. Clean excess silicone.
Light engine
Light engine
Light engine
Radius
Radius
Radius
¾"–1½"
¾"–1½"
¾"–1½"
15
Bends having an inside radius 1½"
or smaller must have electrical
grade silicone applied directly to
the light engine across the bend.
®