DSB CB-240 Petunjuk Pengoperasian

Jelajahi secara online atau unduh pdf Petunjuk Pengoperasian untuk Pembuat buklet DSB CB-240. DSB CB-240 1 halaman.

Halaman Cetak
Operating instructions
CB-240
Instruction manual. . . . . . . . . . . . . . . . . .
Thanks for your purchase.Please carefully read through,
this introduction before use and keep it for future reference.
Operating instructions
CB-240
The machine is designed for binding using plastic binding combs of 6~51 mm. From the following table
you can read off the appropriate binding comb size for the number of sheets you are binding.
Caution: the paper standard is 80g/m .
2
Binding comb dia. 6 8 10 12 14
16
20
22
25
28
32
38
44
50
Max. No. of sheets 25 45 65 95 125 145 175 210 240 270 310 375 440 500
General notes
You should initially carry out sample punching using waste paper. Remember that the maximum punching
capacity is 25 sheets. This specification refers to 80-g-paper (corresponds to the thickness of commercial
copying paper). Punch transparent film and cardboard backs individually.
A scale is drawn on the front plate, with which you can determine the thickness of the document to be
bound(plastic comb guide). Therefore you can easily select the binding comb with the correct width.
Before punching and binding
Right
Left
Figure-1 (select plastic comb size)
Figure-2 (select punching slot)
Hold your document tightly straight,
1.Paper edge guide
5
at three position.
Align
Right
end to get correct measurement
2.Right
for plastic comb dia.6~12mm.
of document thickness and select proper
3.Middle
for plastic comb dia.14~22mm.
plastic comb.
4.Left
for plastic comb dia.14~51mm.
Backward
Left
Right
Frontward
Figure-3 (page stopper-1)
Figure-4 (page stopper-2)
1.Move Page stopper-1
9
backward for
1.Punching the normal paper, you can move
punching normal paper format.
Page stopper-2
10
left or right for different
2.Move Pape stopper-1
9
frontward for
paper format.
punching extra large paper.
2.Make Page stopper-1 align paper format line.
3.
Operating instructions
CB-240
14
1
2
3
4
1
5
14
13
12
11
10
9
8
7
6
1
Description of components
Circulating punching lever : Removable and reassemble handle bar for both extra large and
normal format papers.
Dust cover : Keep the dust falling into the machine
Blades : All blades may be disengaged by pulling them upward manually.
Punching slot : For US pitch 21 ring plastic comb.
Paper edge guide : Left or middle or right 3 steps adjustable punching depth
Plastic comb guide : Determining the binding comb size for your document.
7
Metal comb holding fingers : To hold the plastic comb for opening.
8
Metal hooks : Open plastic comb by hooking the finger rings.
9
Paper stopper-1 : Pushing frontward for punching normal format paper, pushing backward extra
large paper.
10
Paper stopper-2 : By switching
left
or
right
for different format paper.
11
Plastic comb opening lever : Open plastic comb by pulling the lever.
12
Waste bin : Collects waste paper chips
1
(WARNING! Be Sure to Clean Waste Bin Frequently. Overloaded Waste Chips Could Cause
Punching Jam and Machine Damage.)
13
Metal pin : A guide pin for punching extra large paper.
14
Screws : For dividing the circulating punching lever.
1.
How to punch
Punch US pitch for Legal, A4 or LTR Paper Format
2
4
3
1
Figure-5
Figure-6
1
Put the sheets into punching slot
4
,
3
Lift up the circulating punching lever
1
.
left-align
to the page stopper-1
9
.
4
Take out the sheets.
2
Press the circulating punching lever
1
down
strongly with both hands to punch the sheets.
(Note: max.25 sheet 80gsm paper or 2 sheets
PVC cover)
Punch US pitch Extra Large Paper Format
3
1
Move the page stopper-1
9
down.
2
Align the sheets to
A3
line.
3
Press down the single handle lever.
2
1
5
4
Reverse the punched sheets, insert the
third
right end
punched hole to the extended metal
pin
3
(the
Red area
part),
remain two holes
4
at the right side of extended metal pin
3
.
5
Press down the single handle lever.
4.
CB-240
2
11
R
4
R
1
3
4
R
4
3
L
L
5
R
3
2
L
4
2
2.
DSB Commercial Binding
System
Color Ginny
Comb Well
CB-120
CB-230
CB-3000
Technical Data:
Model No.
CB-240
Operating method
Manual
Paper size
Legal, A4, LTR and extra large up to 700mm width
Edge guide
Adjustable in three steps (2.5, 4, 5.5mm)
Punches
24 Selectable punch pins
Punching capacity
25 sheets (80gsm paper), 2 sheets PVC 0.20 mm
Binding comb size
6mm~51mm(500 sheets)
Loading of paper
Vertical
Paper guide line
Multiple(Legal,A4,LTR,A3)
Punching & Binding
Two handles device accept same time operation
Net weight
15Kg
Dimensions
440×480×160(B×D×H)
8.
Punching depth adjustment
1. Set the Paper Edge Guide
5
to the
Right
position (seen from the front) for documents with
comb binding size 6mm to 12 mm. This setting corresponds to the standard setting.
2. Set the Paper Edge Guide
to the
Middle
position (seen from the front) for documents with
5
comb binding size 14mm to 22 mm. The large punching depth prevents tearing of the bound
document.
3. set the Paper Edge Guide
to the
Left
position (seen from the front) for documents with
5
comb binding size 25mm to 51 mm. The large punching depth prevents tearing of the bound
documents.
This is how you punch and bind the sheets of yours document
1. Select a sufficient size of plastic binding comb according to the paper amount (see plastic
comb guide
; Ref.figure-1).
6
2. Place the plastic binding comb into the Metal Comb Holding Fingers
7
with the open side
upwards.
4. The rings are opened by the Metal Hooks
of the comb by pulling the binding back slowly
8
forwards. Stop if the binding comb is opened far enough. The binding comb remains in the
selected position.
5. Put the sheets you want to punch left aligned to the page stopper-1
and push them straight
9
into the punching slot
4
. The page stopper-2
10
is manually adjustable to different formats.
You can use the page stopper-1
for 24 ring punching or for 4-fold punching by moving the
9
page stopper-1
frontward or backward.
9
6. Press the circulating punching lever
1
down strongly with both hands to punch the sheets of
your document.
7. Place the punched sheets in the correct sequence into the opened binding comb.
8. Close the binding comb by pushing the plastic comb-opening lever
11
back. You can then
remove the bound document.
This is how you punch sheets Extra Large Paper Format
1. Loosen 2 screws
on the side of the device.
14
2. Remove the longer part of the lever from the machine.
3. The punching lever can now only be operated with one hand.
4. Place the already punched page into the punching slot
in such a way that you can press
4
one of the holes over the metal pin
13
at the lower end of the slot. This ensures that all holes
have the same distance.
5. Now punch the remainder of the total punching width.
6. Screw the punching lever together again, when you have finished.(refer to "quick tip ......")
This is how you exchange pages of your bound document
1. Place the plastic binding comb (document with writing forwards) into the metal comb holding
fingers
. Pull the plastic binding comb with the bound document between the metal comb
7
holding fingers and lock it into the metal hooks
8
.
2. Press the binding comb carefully backwards until the plastic binding comb opens slightly.
3. You can remove or exchange sheets, when the spiral fingers have opened by approx.4-5 mm.
4. Then close the plastic binding comb by pushing the plastic comb-opening lever
11
.
6.
How to bind
Figure-9
1
Inserting the plastic binding comb in the
Metal Comb Holding Fingers ⑦ with
7
1
the side to be opened
upward.
Figure-10
2
Pull the Plastic Comb Opening lever
11
far enough forward So that the binding
Comb is opened widely.
3
Lay the paper over the comb fingers.
3
2
Figure-11
4
To close the binding comb, push the
plastic comb opening lever
7
downwards.
5
Remove the bound document.
5
4
How to disengage the blades
Depending on the paper format, it is possible to
Disengage any of the 24 blades. to do this, pull the
Unneeded blades upwards. the number of blades
needed For the format being used is given as
followed: Legal/14" with
24
punch holes; A4 with
21
punch holes; LTR with
19
punch holes.
5.
Empty the waste bin
12
2
1
Figure-13
1
Remove the waste bin
completely.
2
Empty the waste chips entirely.
12
3
3
Push the Waste Bin
12
back into the machine.
Warning! Overloaded waste chip in the bin might cause punching jam and machine damage.
Maintenance and care
1. You should regularly empty the waste bin
12
.
2. Films or cardboard should be punched separately.
3. Use the device only for punching paper, cardboard and protective sheets.
7.